Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About 2cellefsen
Stats
Member since
12-07-2004
6
Posts
0
Helpful
0
Solutions
Created by
2cellefsen
in Network Management
in Network Management
04-04-2019
03:24 AM
04-04-2019
03:24 AM
Very useful post, I had exactly the same issue after we got a new batch of 500 2960-L's with updated IOS. The new switches that failed with just IP in the cert came from factory with version 15.2(6)E2b. Switches with 15.2(6)E1 work fine with just IP in the cert. Thank you for a well written solution!
... View more
02-13-2008
01:56 PM
The inlet temperatures of the modules are an indication of the temp of the air beeing drawn into the Catalyst. Your switch seem to be drawing air that is around 28C, which is above the industry general recommended range for a computer room. In the long run this might affect the lifetime of your equipment. Check if your room is colder than the inlet temps, and improve airflow into the switch if you can. Best regards - Oyvind
... View more
Created by
2cellefsen
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
11-28-2006
03:47 AM
11-28-2006
03:47 AM
What do you mean by DMZ controller? Do you think both controllers in your setup need to have itself as anchor?
... View more
Created by
2cellefsen
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
11-28-2006
03:45 AM
11-28-2006
03:45 AM
Hi! I had exactly the same happen to me, only with a 2006 controller initiating the anchor request. Worked fine for a week or two, then just stopped working without any changes. I've had do delete the members in the mobility group on the anchor controller, and then add it again before it started working. Best regards - Oyvind
... View more
11-01-2006
04:40 AM
Hi! If you have traffic between your remote offices (full mesh IP VPN) you might have a challenge, since you can shape outgoing traffic, but have no control on the aggregated incoming traffic to one datacenter or remote office. How well it works depends on how your protocols and applications handle delay and loss. Voice traffic would suffer... Since your SP use ethernet they might only shape your outgoing traffic at the PE, and you are home free. Talk to your SP to find out. Otherwise the mentioned generic shaper underneath might work depending on your hardware and IOS. Best regards - Oyvind
... View more
Created by
2cellefsen
in Server Networking
in Server Networking
03-16-2005
07:29 AM
03-16-2005
07:29 AM
I've done the same while staging some 6500's in the lab, and had to use 10dBm attenuators to avoid overloading the receiver. Depends on how good your cabling and connectors are. Best regards Oyvind
... View more
Created by
2cellefsen
in Network Management
04-04-2019
04-04-2019
Very useful post, I had exactly the same issue after we got a new batch
of 500 2960-L's with updated...
02-13-2008
The inlet temperatures of the modules are an indication of the temp of
the air beeing drawn into the...
Created by
2cellefsen
in Other Wireless - Mobility Subjects
11-28-2006
11-28-2006
What do you mean by DMZ controller? Do you think both controllers in
your setup need to have itself ...
Created by
2cellefsen
in Other Wireless - Mobility Subjects
11-28-2006
11-28-2006
Hi!I had exactly the same happen to me, only with a 2006 controller
initiating the anchor request. W...
11-01-2006
Hi!If you have traffic between your remote offices (full mesh IP VPN)
you might have a challenge, si...
Public Statistics
| Date Registered | 12-07-2004 01:00 AM |
| Date Last Visited | 05-22-2019 12:07 AM |
| Total Messages Posted | 6 |
