Hi, I have two ISP's at my disposal, one of the ASA is utilized as UC proxy and people from internet directly access call manager through the same.. The UC proxy in ASA is configured with one of ISP's IP address block. In case ISP connected to ASA is down, the Unified communication services through internet fails.. Request you to help me i providing solution for UC Proxy failover solution.. Regards ... View more

Hi, I want a low cost solution router with 16 10/100 routed ports...The idea is to club 16 different segments on ofc to this router via media convertor and there will be dynamic protocols such as EIGRP or higher running between these segments.. The router needs to be security enabled...the equipments needs to be a router by defination (not a layer 3 switch)..As per my understanding there is limitation on number of HWIC-2 FE that can be put in ISR G2 series due to which I cannot reach that figure... Kindly let me know if i can use SM-ES3-16-P in the place of HWIC-2FE for this kind of requirement.. Regards Puneet.. ... View more

Hi, I am going to terminate mutiple ISP's connecting on the same 1941 router. After the router there is a ASA5515X device which will be primarily doing IPS as well as perimeter security.. Behind the firewall there are two servers which are going to be accessed by people in internet. I want to ensure that the reachabilty to these servers are up even if one of the ISP goes down... Request you to kindly suggest solution for the same.. Also sending the diagram for the proposed setup for your kind perusal... Regards ... View more

Hi, Would request you to apprise me whether any router in cisco supports the Multi services Card for NAT services... This is one of the specs mentioned which needs to be matched in ASR series routers..... Thanks in advance Puneet. ... View more

Hi, We need to test the following cards in three 7206 routers : PA-8T-V35 PA-VXC-2TE1+ PA-MC-E3 I believe V.35 can be tested connecting back to back... Regarding PA-MC-E3, can I test the card connecting back to back Coaxial Cable for PA-MC-E3 card, if yest kindly help me with the configuration and connectivity part.. Also let me know if I can test PA-VXC-2TE1+ in  a lab environment.... Note that the testing needs to be done in LAB environment. Regards Puneet. ... View more

•1.       We have two locations and require Cisco ACS 5.x for each location. •2.       Both locations are connected via MPLS link. •3.       Need to deploy both ACS in Active-Active OR Active-Standby. •4.       The idea is that users in network A will have their primary ACS as ACS A and secondary ACS as ACS B. •5.       Similarly users in network B will have its primary ACS as ACS B local to their LAN. If ACS in network A goes down, then users in network A should be able to authenticate using ACS B in remote network and vice versa. •6.       Now what we got to understand by reading ACS documents is that incase one of ACS goes down, the accounting logs do not get replicated to secondary ACS and vice versa. •7.       I would like to have a kind of setup where in  Accounting logs are also replicated between ACS servers. The idea is that, I should have complete logs of both the servers up to the time till one of the ACS breaks down. Kindly let me know if the accounting logs can be replicated in the manner as mentioned above. Also let me know the typical bandwidth utilized during replication of ACS A to ACS B. We have around 500 users combining both sides. Our proposal is dependent upon working of the above solution…kindly see if ACS5.x will work in the above scenario as we need to propose the same. ... View more

Hi, I am looking for a very basic port density based requirement which should provide the cheapest solution...My requirement is : 1. 3 x 10/100/1000 Gigabit Ethernet 2. 1 port of VWIC2-2MFT-G703... Kindly let me know if EHWIC-1GE-SFP-CU can be taken in 1921 router to suffice the requirement as this comes out to be the cheapest solution. I have reservations about EHWIC-1GE-SFP-CU as this can support upto 800Mbps of throughput. Or do I need to go with 2911 which has 3 onboard 10/100/1000 ports... Kindly help... Regards Puneet ... View more