We have configured tunnel interface in the L3(6509) switch to pass traffic through different route inspite of passing through existing route. for this purpose we have given the static route from source(6509 SW)to the Dest.(gateway router Bharti),the dest. is pinging the source, but the icmp traffic is not coming ( not pinging ) from source to the dest.Is it required to configure Back-route from dest. to source. Please suggest me.How to solve the problem. thanks, Dhiman ... View more

Can u please tell me how to configure IPS in cisco router and how to upload the signature to the router...please give the logical explanation and comman line for the same. Please suggest me. Thanks Dhiman ... View more

We are facing the problemwhen we are booting the 3620 router.continuosly it is booting itself and showing the error which is attached here..please suggest us what the problem is.... thanks in advance ... View more

Is there any latet IOS for 3620 (12.0) router ....is there any..please gine the link...thanks in advance ... View more

I am going to insert a redundant Supervisor engine-2 in 6509 switch.What steps I should follow to install the same.Please suggest me with the detailed configuration ... View more

OLD IOS:- (C2800NM-ADVSECURITYK9-M), Version 12.4(3g), RELEASE SOFTWARE (fc2) "flash:c2800nm-advsecurityk9-mz.124-3g.bin" This IOS is not supporting Mpls ....but supports Ips,IDS,Firewall and VPN New IOS :- (C2800NM-ENTSERVICESK9-M), Version 12.4(10c) This IOS suppots MPLS but not the IPS,IDS,Firewall and VPn... Could it be possible to support both functions in same IOS in 2811 router...pls suggest.Thank tou. Dhiman "flash:c2800nm-entservicesk9-mz.124-10c.bin ... View more

Is it possible to configure the loopback address in cisco 2950 switch. The command is there in switch,but when i am entering the correct syntax to configure the same I am getting the below mentioned Switch(config)#int loopback 0 ^ % Invalid input detected at '^' marker. Please suggest what should we do configure the loopback address in L2 sw. the existing IOS is c2950-i6q4l2-mz.121-22.EA9.bin" is it required to upgarade? ... View more

I want to configure DNS in router having two default routes...how it can be possible? after configuring I can't ping the DNS server from router.... ... View more

Scenario of Inter-Vlan routing between PIX and L3 (SW 6509) Under the core routers sub-interfaces, the voice vrf is directly going to LVI of 6509 switch. But NON-MPLS traffic is directly going to gateway of backbone zone of pix. The details we have mentioned below 1) For Voice vrf traffic we have created the sub-interface fe0/0.50 in CR2 and the gateway for that network is in vlan 50 (LVI) in Core Sw 6509. Also we have created the sub-interface fe0/0.6 for the non-mpls ip traffic (ip routing). what ever the vlans (Different LVI for VLANs) are coming under the inside zone , those vlans are routed to the inside zone interface of PIX with the help of ospf process 1, area1, because the default-route for that vlans is in PIX.But the backbone interface of PIX is in Area0. 2) we are creating separate zone in the existing pix for placing of NMS,EMS servers and only one vlan will be created in the 6509 switch without ip address (Transparent) for placing the NMS/EMS servers. But the gateway of this vlan is pointing to the NMS/EMS zone of pix firewall. That means in switch this vlan is acting as a transparent only.If any packet is coming to the NMS/EMS zone, that will come via BACKBONE zone interface of PIX. Please suggest how we can map the NMS/EMS vlan (under the NMS/EMS Zone) to core routers sub-interface ,that sitting under the backbone zone of same pix also how can it be possible to route the non-mpls packet to NMS/EMS vlan (part of the NMS/EMS vrf). Our requirement is to make the communication in between vrf and non-vrf traffic in a same vlan. Is it actually possible for a single vlan to be the part of vrf traffic and non-mpls ip traffic at the same time? Please suggest us. ... View more

Where and how to configure MCID in Call Manager and how to trace the Malicious Call...please tell... ... View more

how and where to configure Direct Inward Dial(DID) and Dial Outward Dial (DOD).And what are the results? ... View more

Can all of u please tell me how and where to configure Distinctive Ring ( on-net vs. off-net),Distinctive Ring per line appearance and Distinctive Ring per phone is configured in call manager ... View more

How to make the communication in between two clusters (each is having 3000 ip phones)of same capacity,if any trunk is needed ... View more