About dot1x

dot1x · ‎03-03-2020

Hi Champs, We need to implement an outdoor wireless mesh for the attached plan. Since it's a remote site, it's not possible to do an on-site survey. Based on the locations of the light poles, we were thinking to install 2 RAPs. Point to Multipoint Link from RAP1 to P1 and P2 Point to Multipoint Link from RAP2 to P3 and P5 We would need 5GHz for backhaul and 2.4GHz to serve the clients. We are thinking to go with 3504 WLC and 1560E APs (Flex+Bridge Mode). Could someone please take a look and suggest the antennas that would serve this purpose? Thanks.

dot1x · ‎03-02-2020

Hi Champs, We need to implement an outdoor wireless mesh for the attached plan. Since it's a remote site, it's not possible to do an on-site survey. Based on the locations of the light poles, we were thinking to install 2 RAPs. Point to Multipoint Link from RAP1 to P1 and P2 Point to Multipoint Link from RAP2 to P3 and P5 We would need 5GHz for backhaul and 2.4GHz to serve the clients. We are thinking to go with 3504 WLC and 1560E APs (Flex+Bridge Mode). Could someone please take a look and suggest the antennas that would serve this purpose? Thanks.

dot1x · ‎09-01-2019

@Sandeep Choudhary wrote: Check if client is using the wrong password! 1. try to ignote/forget the wlan on clinet 2. delete the mac address of clinet from Exlusion list 3. try again to connetc to wlan with correct password. Rergards Dont forget to rate helpful posts Hi Sandeep, Thanks for your reply. I've tried all these already, nothing worked. I've now disabled client exclusion and able to connect now. Still wondering if there's a way to fix this without disabling this feature?

dot1x · ‎09-01-2019

Hi All, We are running Cisco Mobility Express v8.3.133.0 on 2800 Series APs. One of the clients has been excluded and won't connect. From CLI, I used following command to delete the excluded client but the client still wont' connect and goes into exclusion list. config exclusionlist delete <MAC Address> Any thoughts?

dot1x · ‎08-25-2019

@Rasika Nayanajith wrote: You can do either way (console, ssh to redundancy management or service port of standby unit) If you have SSH access to redundancy management IP of standby unit, you can verify it remotely. YOu (WLC1-Standby) >show interface summary management LAG 1000 x.x.x.200 Static Yes No redundancy-management LAG 1000 x.x.x.201 Static No No service-port N/A N/A x.y.y.201 Static No No HTH Rasika Hi Rasika, It says LAG enabled. All we need to do now is to configure the switchports in etherchannel and connect the cables?

dot1x · ‎08-25-2019

@Rasika Nayanajith wrote: You should be able to run "show lag summary" command on standby unit (WLC1-Standby) >show lag summary LAG Enabled HTH Rasika *** Pls rate all useful responses *** Thanks Rasika. We would need a console/service port access to run this command, right?

dot1x · ‎08-25-2019

If it is already in SSO, secondary may already configured with LAG. Are you sure that unit is not configured with LAG ? I'm not sure. Is there a way to check it on secondary while the HA is still in place?

dot1x · ‎08-25-2019

Hi All, A quick question: We have 2 WLCs in HA SSO. On Primary, LAG is configured and all the ports are being used. On Secondary WLC, only 1 port is being used. We would like to use all the ports on the Secondary WLC, what's the best way to go about it? Do we need to disable the HA or this could be done without breaking the HA? Thanks.

dot1x · ‎07-27-2019

@ciscoazlancco wrote: So, as the far end bridged AP does has a wired connection to the controller, how will it detect the controller ? By means of a wireless connection ? Or does it need a temporally wired connections to set up, broken up afterwards ? That's how we did it, temporarily wired connected the AP to set it up and then broken up.

dot1x · ‎07-15-2019

@ciscoazlancco wrote: I heard somewhere that wireless bridge between given two buildings is now also possible with 1562 I/E/D without controller. Is this correct ? I suppose with the " Lightweight AP Software" ? What particular software version ( or above ) is needed ? Lightweight AP Software works with Controller. Since there is no Autonomous Software available, the wireless bridge won't work without a controller.

dot1x · ‎06-23-2019

Yes, we did.

dot1x · ‎01-31-2019

HA SSO

dot1x · ‎01-31-2019

Master AP Model Maximum APs Supported Maximum Clients Supported Cisco Aironet 1540 Series 50 1000 Cisco Aironet 1560 Series 100 2000 Cisco Aironet 1815i 50 1000 Cisco Aironet 1815m 50 1000 Cisco Aironet 1815w 50 1000 Cisco Aironet 1830 Series 50 1000 Cisco Aironet 1850 Series 50 1000 Cisco Aironet 2800 Series 100 2000 Cisco Aironet 3800 Series 100 2000

dot1x · ‎01-31-2019

Thanks Leo. Do we need to push configs to both 3504s or just primary? And the 2nd 3504 will get the config when we create the HA?

dot1x · ‎01-31-2019

Thanks Leo. Do we need to push configs to both 3504s or just primary? And the 2nd 3504 will get the config when we create the HA?

dot1x · 03-03-2020

Hi Champs,We need to implement an outdoor wireless mesh for the attached plan.Since it's a remote si...

dot1x · 03-02-2020

Hi Champs, We need to implement an outdoor wireless mesh for the attached plan.Since it's a remote s...

dot1x · 09-01-2019

@Sandeep Choudhary wrote:Check if client is using the wrong password!1. try to ignote/forget the wla...

dot1x · 09-01-2019

Hi All, We are running Cisco Mobility Express v8.3.133.0 on 2800 Series APs.One of the clients has b...

dot1x · 08-25-2019

@Rasika Nayanajith wrote:You can do either way (console, ssh to redundancy management or service por...

dot1x · 08-25-2019

@Rasika Nayanajith wrote:You should be able to run "show lag summary" command on standby unit (WLC1-...

dot1x · 08-25-2019

If it is already in SSO, secondary may already configured with LAG. Are you sure that unit is not co...

dot1x · 08-25-2019

Hi All, A quick question: We have 2 WLCs in HA SSO.On Primary, LAG is configured and all the ports a...

dot1x · 07-27-2019

@ciscoazlancco wrote:So, as the far end bridged AP does has a wired connection to the controller, ho...

dot1x · 07-15-2019

@ciscoazlancco wrote:I heard somewhere that wireless bridge between given two buildings is now also ...

dot1x · 06-23-2019

Yes, we did.

dot1x · 01-31-2019

HA SSO

dot1x · 01-31-2019

Master AP Model Maximum APs Supported Maximum Clients Supported Cisco Aironet 1540 Series 50 1000 Ci...

dot1x · 01-31-2019

Thanks Leo.Do we need to push configs to both 3504s or just primary?And the 2nd 3504 will get the co...

dot1x · 01-31-2019

Thanks Leo. Do we need to push configs to both 3504s or just primary? And the 2nd 3504 will get the ...

Date Registered	‎06-13-2017 09:32 PM
Date Last Visited	‎03-04-2020 12:17 AM
Total Messages Posted	187
Total Helpful Votes Received	15

Point to Multipoint Outdoor Mesh/Bridge

Re: Outside parking Wireless Coverage B...

Re: Cisco Mobility Express - Excluded C...

Cisco Mobility Express - Excluded Clien...

Re: Enabling LAG on Secondary WLC (HA)

Re: Enabling LAG on Secondary WLC (HA)

Re: Enabling LAG on Secondary WLC (HA)

Enabling LAG on Secondary WLC (HA)

Re: Wireless Bridge using Mobility Expr...

Re: Wireless Bridge using Mobility Expr...

Re: 1532E Point to Point Bridge - WAN a...

Re: Cisco WLC config migration from 250...

Re: Number of clients Mobility Express ...

Re: Cisco WLC config migration from 250...

Re: Cisco WLC config migration from 250...

Point to Multipoint Outdoor Mesh/Bridge

Re: Outside parking Wireless Coverage Best Access Points and Antennas

Re: Cisco Mobility Express - Excluded Client

Cisco Mobility Express - Excluded Client

Re: Enabling LAG on Secondary WLC (HA)

Re: Enabling LAG on Secondary WLC (HA)

Re: Enabling LAG on Secondary WLC (HA)

Enabling LAG on Secondary WLC (HA)

Re: Wireless Bridge using Mobility Express

Re: Wireless Bridge using Mobility Express

Re: 1532E Point to Point Bridge - WAN and LAN Interface Confusion

Re: Cisco WLC config migration from 2504 to 3504

Re: Number of clients Mobility Express handles

Re: Cisco WLC config migration from 2504 to 3504

Re: Cisco WLC config migration from 2504 to 3504