Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About ajagadee
06-17-2019
ajagadee
Member since
12-06-2002
Cisco Employee
Arul Jagadeesan is a Network Consulting Engineer and part of the Advanced Services Team in Richardson, Texas. Arul has a Master's Degree in Electrical Engineer and Bachelor Degree in Electronics and Communication Engineering from University of Madras, India.
Arul joined Cisco Systems in 2001 as an Customer Support Engineer in the Technical Assistance Center (TAC). Arul Jagadeesan, CCIE# 9942, holds CCIE certifications in Routing and Switching & Security.
Arul Jagadeesan is a Network Consulting Engineer and part of the Advanced Services Team in Richardson, Texas. Arul has a Master's Degree in Electrical Engineer and Bachelor Degree in Electronics and Communication Engineering from University of Madras, India.
Arul joined Cisco Systems in 2001 as an Customer Support Engineer in the Technical Assistance Center (TAC
02-25-2009
08:25 PM
Pedro, I am not an ATM Expert but let me try and explain this to you. I think your provider is using bps conversion of 384, that is 48 Bytes per cell. Typically, the value of 384 is used when the reference date is the non ATM entering an ATM core. 48 * 8 = 384. So, (7.22 * 384)/60 = 46.208 Regards, Arul *Pls rate all helpful posts*
... View more
02-25-2009
07:40 PM
Hello Andrew, It is my understanding that KS and GM on the router is not supported. Regards, Arul *Pls rate all helpful posts*
... View more
12-25-2008
09:17 PM
Hi, Below is the "show version" output from a 2611xm. I hope it helps. 2600#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(40), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 12-Oct-06 21:01 by pwade Image text-base: 0x8000808C, data-base: 0x8111D524 ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1) chi-2600-8 uptime is 22 weeks, 1 day, 12 hours, 50 minutes System returned to ROM by reload System image file is "flash:c2600-is-mz.122-40.bin" cisco 2611XM (MPC860P) processor (revision 0x100) with 93184K/5120K bytes of mem ory. M860 processor: part number 5, mask 2 Bridging software. X.25 software, Version 3.0.0. 2 FastEthernet/IEEE 802.3 interface(s) 2 Low-speed serial(sync/async) network interface(s) 32K bytes of non-volatile configuration memory. 49152K bytes of processor board System flash (Read/Write) Regards, Arul
... View more
12-24-2008
08:50 AM
Scott, Yes, it should be possible to configure the ASA5505 to accept L2L connection from Dynamic IP. Please refer the below URL for configuration details: http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805733df.shtml Regards, Arul *Pls rate all helpful posts*
... View more
12-23-2008
07:50 PM
Timothy, I dont think its possible to configure the same vlan under two different interface. In order to provide physical link redundancy, you can use the "Link Redundancy Feature" which was introduced in 8.0 code and higher. More information in the below URL: http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/intrface.html#wp1045838 Regards, Arul *Pls rate all helpful posts*
... View more
12-23-2008
11:58 AM
Hi, Glad to be of help. Could you update the forum that the solution resolved the issue, so others who run into similar issue can benefit out of the post. Thanks! If the prod network is on the inside interface: static (inside,dmz) 192.168.2.8 192.168.2.8 By default, there are not ACLs applied on the inside interface. In case if you have configured one, make sure that you permit the necessary ports/protocols for this server. Regards, Arul *Pls rate all helpful posts*
... View more
12-23-2008
10:36 AM
Jacob, I dont think there is a configuration command to disable the activation key. One option is to erase all the contents in the flash and the only way to recover the pix is through monitor mode and at that time the pix should prompt for the activation key. And this way you clear the activation key as well. Regards, Arul *Pls rate all helpful posts*
... View more
Created by
ajagadee
in Security Analytics and Management
in Security Analytics and Management
12-23-2008
09:48 AM
12-23-2008
09:48 AM
Hi, Please refer the below URL for configuration details: http://www.cisco.com/en/US/docs/ios/12_0t/12_0t3/feature/guide/Snmp3.html Regards, Arul *Pls rate all helpful posts*
... View more
Created by
ajagadee
in VPN and AnyConnect
in VPN and AnyConnect
12-23-2008
09:32 AM
12-23-2008
09:32 AM
Tom, From the debugs, it looks like the router is transmitting Phase 1 Packets and never seeing a response. This basically means, ISAKMP ports are blocked somewhere. That is UDP Port 500. Can you make sure that the below ports and protocols are open between the Router and Sonicwall. ISAKMP - UDP 500 ESP - Protocol 50 ISAKMP NAT-Traversal - UDP 4500 (NAT-T) Regards, Arul *Pls rate all helpful posts*
... View more
12-22-2008
09:34 PM
Chris, Glad to be of help. Please do update the forum on the results from your prod deployment. Regards, Arul
... View more
12-22-2008
07:33 PM
Jonathan, I believe you can enable PPPoE only on the outside interface and the interface has to be name "outside" and the name is case sensitive. For example, if you configure the E0 with OutSide and try to enable PPPoE, the chassis will return the above error message. Example 1: pixfirewall(config)# nameif e0 PPP sec0 pixfirewall(config)# ip add PPP pppoe PPPoE client can only be started on outside interface Example 2: pixfirewall(config)# nameif e0 OutSide se0 pixfirewall(config)# ip add OutSide pppoe PPPoE client can only be started on outside interface So, your only option is to reconfigure the outside interface with a name of "outside" and then configure PPPoE. Regards, Arul *Pls rate all helpful posts*
... View more
12-22-2008
02:12 PM
Hi, Please refer the below URL for configuration details: Configuring Router-to-Router Dynamic-to-Static IPSec with NAT http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080093f86.shtml Regards, Arul *Pls rate all helpful posts*
... View more
12-22-2008
11:23 AM
Andrew, After you configure the above statement, where are you sourcing the ICMP packets from and what is the destination. I believe below statement will translate the outside IP 12.12.12.10 to 172.16.1.200 and then you need a translation for whatever destination the IP Address is. For example: Router 1.1.1.1 - Inside ASA - Outside - 12.12.12.10 static (outside,inside) 172.16.1.200 12.12.12.10 netmask 255.255.255.255 static (inside,outside) 1.1.1.1 1.1.1.1 netmask 255.255.255.255 ciscoasa(config)# sh xlate 2 in use, 2 most used Global 1.1.1.1 Local 1.1.1.1 Global 172.16.1.200 Local 12.12.12.10 So, if I telnet to 1.1.1.1 from the outside with 12.12.12.10, the packets get translated to 172.16.1.200 on the ASA and then the ASA looks for the regular inside/outside translation for the destination. That is why I have a static (inside,outside) for 1.1.1.1. Router that is configured with IP 1.1.1.1 interface Loopback101 ip address 1.1.1.1 255.255.255.0 7140#sh users Line User Host(s) Idle Location * 0 con 0 idle 00:00:00 2 vty 0 idle 00:02:27 172.16.1.200 I hope it helps. Regards, Arul *Pls rate all helpful posts*
... View more
12-22-2008
11:15 AM
The no failover active command is entered on the active unit, or the failover active command is entered on the standby unit. http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00807dac5f.shtml Regards, Arul *Pls rate all helpful posts*
... View more
Created by
ajagadee
in VPN and AnyConnect
in VPN and AnyConnect
12-22-2008
11:13 AM
12-22-2008
11:13 AM
Michael, While, it is possible to assign IP Addresses for the VPN RA Users from your internal subnet, it is not recommended. The reason being due to ARP, Proxy ARP, Routing, NONAT, ACL, etc and also makes troubleshooting hard. Also, depending upon your set up, it is easy to track usage, netflow statistic, etc. Most of the times, in this forum as well as others, you will always see the recommendation is to use a different range of ip addresses other than your internal subnet. And if I were you, that is what I would do. Regards, Arul *Pls rate all helpful posts*
... View more
02-25-2009 08:25 PM
Pedro,I am not an ATM Expert but let me try and explain this to you.I
think your provider is using b...
02-25-2009 07:40 PM
Hello Andrew,It is my understanding that KS and GM on the router is not
supported. Regards,Arul*Pls ...
12-25-2008 09:17 PM
Hi,Below is the "show version" output from a 2611xm. I hope it
helps.2600#sh verCisco Internetwork O...
12-24-2008 08:50 AM
Scott,Yes, it should be possible to configure the ASA5505 to accept L2L
connection from Dynamic IP. ...
12-23-2008 07:50 PM
Timothy,I dont think its possible to configure the same vlan under two
different interface. In order...
12-23-2008 11:58 AM
Hi,Glad to be of help. Could you update the forum that the solution
resolved the issue, so others wh...
Created by
ajagadee
in Security Analytics and Management
12-23-2008 09:48 AM
12-23-2008 09:48 AM
Hi,Please refer the below URL for configuration
details:http://www.cisco.com/en/US/docs/ios/12_0t/12...
Created by
ajagadee
in VPN and AnyConnect
12-23-2008 09:32 AM
12-23-2008 09:32 AM
Tom,From the debugs, it looks like the router is transmitting Phase 1
Packets and never seeing a res...
12-22-2008 09:34 PM
Chris,Glad to be of help. Please do update the forum on the results from
your prod deployment.Regard...
12-22-2008 07:33 PM
Jonathan,I believe you can enable PPPoE only on the outside interface
and the interface has to be na...
12-22-2008 02:12 PM
Hi,Please refer the below URL for configuration details:Configuring
Router-to-Router Dynamic-to-Stat...
12-22-2008 11:23 AM
Andrew,After you configure the above statement, where are you sourcing
the ICMP packets from and wha...
Created by
ajagadee
in VPN and AnyConnect
12-22-2008 11:13 AM
12-22-2008 11:13 AM
Michael,While, it is possible to assign IP Addresses for the VPN RA
Users from your internal subnet,...
Public Statistics
| Date Registered | 12-06-2002 04:34 PM |
| Date Last Visited | 06-17-2019 01:08 PM |
| Total Messages Posted | 1,474 |
| Total Helpful Votes Received | 2128 |
Helpful Votes Given To
Helpful Votes From
