About RAMAN AZIZIAN

RAMAN AZIZIAN · 08-17-2021

Hello Friends,I have been chasing the following issue and can't seem to figure out what is going on.I have ISE appliance running 2.7. I have applied the latest patch as well.TACACS has been configured for device management.I have multiple IOS 93k Swi...

RAMAN AZIZIAN · 04-07-2021

Hello Everyone,I have SMC 2210, FC 4210, FS 3210 in my network. Stealthwatch 7.3.1 is running on all the appliances.Quick overview of problem:I am not seeing any traffic being reported on interfaces that are being monitored on the switches (exporters...

RAMAN AZIZIAN · 09-30-2020

Hello,I am attempting to configure my ISR4431 with T1 cards to perform drop and insert. Basically its not working, meaning the channels being inserted are not being seen on the other side.I want to take a 1 channel out (Raw data) of one T1 (Channel 2...

RAMAN AZIZIAN · 05-06-2020

Hello everyone,I can't seem to figure out the logic behind the policy set to authenticate and authorize my users based on the privilege and device type. Sorry for the lengthy description.I have a couple of ISE 3615 appliances, running version 2.6. On...

RAMAN AZIZIAN · 09-30-2019

Hello, I'm in the process of developing the CoPP policy for our network, and I'm having difficulty finding info on how to map the Policing CIR for each classification.I know it will be case by case, but I wanted to find out if there is a formula to ...

RAMAN AZIZIAN · 08-18-2021

Thanks Richard for looking at this.I will try it this afternoon and see if I can get the debug output. I did look at the log on the switch, and the switch clearly indicates that I have successfully logged in. There is no indication at all that it fai...

RAMAN AZIZIAN · 04-09-2021

Adding the following two commands did the job.collect timestamp absolute firstcollect timestamp absolute last Also, this site helped tremendously to get the config per platform. https://configurenetflow.info/

RAMAN AZIZIAN · 04-08-2021

hello Ben,would you mind providing me a sample of the config? I am looking into the doc you provided, but I am not sure I'm seeing what you are referring to.I do see the following and not sure if this is what you are referring to.collect timestamp ab...

RAMAN AZIZIAN · 09-30-2020

The clock is being provided (simulating Service provider) via an external appliance/device. The two T1's which connect to the appliance, have no issues in regard to Bit errors/Frame loss or anything along that line.

RAMAN AZIZIAN · 09-30-2020

hello Georg,I checked that and made sure it was enabled. I am still having sync issue.On Site A, the T1 port P1, When I perform a loopback local line, the test set syncs up with no issues. I drop the loop and then issue the loop command on P0, thinki...

Member Since	‎02-16-2007 08:10 AM
Date Last Visited	‎07-25-2024 05:42 AM
Posts	86
Total Helpful Votes Received	1

User Statistics

User Activity

Authorization fails on Switch, but ISE indicates success

Stealthwatch SMC not reporting data in the dashboard for the exporters in the monitor menu

T1 Drop and Insert connectivity issue - Need to verify my configs please

ISE AAA TACACS+ authentication with NX-OS and IOS - My policy set appears to accept one or the other

CoPP policing Rate Limit for IGP, mgmt, etc

Re: Authorization fails on Switch, but ISE indicates success

Re: Stealthwatch SMC not reporting data in the dashboard for the exporters in the monitor menu

Re: Stealthwatch SMC not reporting data in the dashboard for the exporters in the monitor menu

Re: T1 Drop and Insert connectivity issue - Need to verify my configs please

Re: T1 Drop and Insert connectivity issue - Need to verify my configs please