About techinneed

techinneed · 11-23-2019

Hello all,Need a little help here.I have a switchport interface in a port-channel group. Currently the physcial switchport is not taking any errors, no CRCs, input errors or link status changes. When I look at the results from a "show interface et1...

techinneed · 12-13-2016

Hello All, We are putting our dark fiber in line, and will need to select the channels we want to use. Normally channel 21 - 36 are used first. I think this has to do with channel spacing 50GHz vs 100GHz vs 200GHz, but I could be wrong. Any insi...

techinneed · 06-20-2015

Hello all, I am trying to figure out why the maximum wireless speed my laptop gets is 11Mbps when connected to the 1240ag WAP.No matter what I change or adjust on the WAP the speed never exceeds 11Mbps. This speed is not really good for streaming c...

techinneed · 12-17-2014

All, I configured vtp version on a switch incorrectly. I changed it to VTP Ver 2, and then changed it back to VTP Ver 1. When I do a sho vtp status: It still shows me VTP version 2. Why is this? Is there any way for me to change this back to Ver ...

techinneed · 10-12-2014

Hello All, I have two C1240AG WAPs and I need to configure them on the office network which has one LAN. The managers wants me to create a guest WIFI from these WAPs. I have one firewall, and one switch for the office. Can someone point me in the rig...

techinneed · 11-24-2019

Cisco Catalyst 9300 Series switch1 %EC-5-UNBUNDLE Interface Et1/1 has left Port-Channel1switch1 %EC-5-BUNDLE: Interface Et1/1 has joined Port-Channel1 Yes, Et1/1 is the only interface in the port-channel I do not understand your statement below:"In g...

techinneed · 11-24-2019

I do not have the config for the other side as it belongs to a client. interface po1 load-interval 5 ip address 1.1.1.1 255.255.255.252 spanning-tree bpdufilter enable interface et1/1 load-interval 5 no switchport channel-group 1 mode act...

techinneed · 06-23-2015

Hello all, Just a little update. For whatever reason, on the C1242ag WAP, I disabled the 802.11g Radio and the bandwidth on the laptop went from 11Mbps up to 48Mbps. Currently on this WAP, it only has the 802.11a radian enabled. How is this so? I t...

techinneed · 06-21-2015

Thanks for getting back to me. The laptop is off right now, and I cannot check the driver, but I did try to upgrade the driver, and the upgrade wizard had a message that the latest driver is installed. The driver can do 802.11a/b/g/n or one of each...

techinneed · 12-17-2014

Thanks Alex. So basically the answer is no, I cannot change it back to VTP ver 1. All the other switches are set to VTP ver 1, which is why I wanted to change it back. I think if I understand your post, I cannot change it back to VTP ver 1. Is this ...

Member Since	‎12-30-2011 04:30 PM
Date Last Visited	‎12-01-2019 11:42 AM
Posts	57

User Statistics

User Activity

LACP and LAG Phantom Issue

Any standard to select DWDM channels

Maximum speed for a Aironet 1240ag WAP

Changing switch (c3750) from VTP Ver 2 to 1

Have two C1240AG WAPs

Re: LACP and LAG Phantom Issue

Re: LACP and LAG Phantom Issue

Hello all, Just a little

Thanks for getting back to me

Thanks Alex. So basically the