Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About gabriel.barrios
Stats
Member since
03-16-2005
5
Posts
0
Helpful
0
Solutions
Created by
gabriel.barrios
in Security Documents
in Security Documents
05-26-2017
07:58 AM
05-26-2017
07:58 AM
Hi, it seems the video only last 5secs. could you post the complete one? thanks Gabriel
... View more
on wired, we have via cdp or
in Wireless Security and Network Management
09-26-2016
01:18 PM
09-26-2016
01:18 PM
on wired, we have via cdp or on third parties ToIP phones the feature called: eap proxy logoff. So the phone "spoof" PC mac address and sends to the switch a "eap-logoff".
It only applies to EAP authentication, not MAB.
Hope it helps
... View more
09-07-2016
11:13 PM
same problem here. When a user leaves the wired connection and comes back, it may appear the issue.
We also have the BIOS setting to switch from wired-to-wireless or vice versa enabled (it disables wifi when wired connection is present).
still looking,
did you find the solution?
thanks!!
... View more
05-11-2016
02:26 AM
Hi Nazmul,
We have setup in the lab a test with the following connections:
PC1----netmod1port1-------Sourcefire 8130-----netmod1port2-----PC2
PCs are Windows 7, with speed auto, duplex auto, Giga capable. Fixed IP address.
8130 is configured with: speed auto, duplex auto, Auto-Midix and propagate link state.
With the 8130 turned on, we run a ping and it works ok. We turn off the 8130 and we have a network outage of 8 segs, then we see ping working ok back again.
If we turn on the 8130, after 15min, we have a network outage again, of 8 segs, and after that, we see ping working ok back again.
Any help?
Thanks!
gabriel
... View more
Created by
gabriel.barrios
in Wireless and Mobility
in Wireless and Mobility
04-11-2015
11:38 AM
04-11-2015
11:38 AM
Hi all, need some help. Its just installed a CSM, v.4.8. It adds a device and its configuration from the network, a FW ASA 8.3 correctly. i make a change on the local policy and as soon i make a deploy to device it start doing a: no xxxx no xxxx1 no xxxx2 for each line of the current configuration! so it deletes all! I am missing a point in here. User guide says that i have to bind a policy to the device but that easy step i do not know how to do it. thanks in advance for the help Regards José
... View more
Labels:
01-06-2015
12:42 AM
as far as i know, they are embedded into the properties of each certificate. Look for the details of it. it will be your RADIUS (NPS, ISE or WLC if doing the end tunnel termination) the one that request the CRL via http or ldap. hope it helps
... View more
Created by
gabriel.barrios
in VPN and AnyConnect
in VPN and AnyConnect
10-10-2013
01:21 PM
10-10-2013
01:21 PM
Have you try to do a Proxy Bypass at the ASA? You will find it at: Configuration----RemoteAccessVPN---Clientless---Advanced---ProxyBypass You may use wildcard for your internal website. Hope it helps Gabriel
... View more
Created by
gabriel.barrios
in Security Documents
in Security Documents
12-07-2010
04:14 AM
12-07-2010
04:14 AM
Take care if you have it on HA (failover). When the first license expires, that appliance differs to the other one and the failover gets disabled!. One goes for failover disabled and second one to failover-pseudo-disabled. You wont have HA and you have to renew the botnet license. As soon you applied back to the 2 appliances, and restore the failover on the primary, the secondary comes back automatically (from pseudo-failover to secondary-active-ready). hopes it helps
... View more
Created by
gabriel.barrios
in Security Documents
05-26-2017
05-26-2017
Hi, it seems the video only last 5secs. could you post the complete
one?thanksGabriel
Created by
gabriel.barrios
in Wireless Security and Network Management
09-26-2016
09-26-2016
on wired, we have via cdp or on third parties ToIP phones the feature
called: eap proxy logoff. So t...
09-07-2016
same problem here. When a user leaves the wired connection and comes
back, it may appear the issue. ...
05-11-2016
Hi Nazmul, We have setup in the lab a test with the following
connections: PC1----netmod1port1------...
Created by
gabriel.barrios
in Wireless and Mobility
04-11-2015
04-11-2015
Hi all, need some help. Its just installed a CSM, v.4.8. It adds a
device and its configuration from...
01-06-2015
as far as i know, they are embedded into the properties of each
certificate. Look for the details of...
10-10-2013
Have you try to do a Proxy Bypass at the ASA?You will find it
at:Configuration----RemoteAccessVPN---...
Created by
gabriel.barrios
in Security Documents
12-07-2010
12-07-2010
Take care if you have it on HA (failover). When the first license
expires, that appliance differs to...
Public Statistics
| Date Registered | 03-16-2005 12:11 PM |
| Date Last Visited | 06-16-2018 12:08 AM |
| Total Messages Posted | 5 |
