Hi, we have a strange issue. We are company, which are located in several countries. For all outgoing calls, we are using one Sip-Gateway which is located in Israel. Now we have the following issue. 1. We call a mobile number which is located in UK (the codec that is used is G711alaw) 2. We do an internal transfer to another phone in the company. The call can be picked up, and we can speak which each other. To transfer the call I press the button "Transfer" on the phone 3. The call is still alive, but on both ends you are not able to hear each other. The signalling is working, the Voice stream not. At that moment the codec is G711ulaw We only have this problem for mobile numbers in UK. Mobile phones in Europe are working. Landline in UK are working as well. If I do a conference call, instead of Transfer, it is working as well If I use the local breakout from UK or from Switzerland it is also working Does anyone has an idea?? Thanks in advance Frank ... View more

Hi all,     I have a problem regarding PBR on a Cisco 4500-X. I`d like to configure a source routing from the IP address 192.168.217.52 over the address 192.168.211.6 instead of the "normal" default route (192.168.200.50). Therefore I configured the following: access-list 101 permit ip host 192.168.217.52 any    route-map gold permit 10  match ip address 101  set ip next-hop 192.168.211.6 interface Vlan217  ip address 192.168.217.1 255.255.255.0  no ip redirects  no ip proxy-arp  ip policy route-map gold   Unfortunately it does not work. If I do a traceroute I can observe that still the default route is active:   C:\Users\schoerlf>tracert -d 8.8.8.8 Tracing route to 8.8.8.8 over a maximum of 30 hops   1     2 ms     8 ms     2 ms  192.168.217.1   2     1 ms     1 ms     1 ms  192.168.200.50   3     2 ms     2 ms     2 ms  157.161.177.70   4     4 ms     3 ms     3 ms  157.161.253.237   5    34 ms    28 ms    27 ms  157.161.197.252   6     2 ms     2 ms    12 ms  157.161.254.5   7     4 ms     3 ms     4 ms  91.206.52.74   8    10 ms     9 ms     9 ms  72.14.232.120   9     9 ms     9 ms     9 ms  72.14.234.235  10     9 ms     9 ms     9 ms  209.85.254.118  11     *        *        *     Request timed out.  12     9 ms     9 ms     9 ms  8.8.8.8   T&R Frank ... View more

Hi all, I have a Cisco ISE server, which is installed on a VMWare plattform. On the ISE server, I configured 2 network cards. One for the Corporate network ( Gigabit Ethernet 0) and one for the Guests (Gigabit Ethernet 1). Because I had problems, I put a client into the Guest VLAN (Wired) and tried to access the guest portal which was not working. I recognized that the port 8443 for the guest portal is blocked. But I was able to ping the address, and the port 443 and 22 are open as well. On the Gigabit Ethernet 0 network everything works. All interfaces are activated at the Web Portal Management Settings, for the ports 8443 and 8444. Anybody an idea?? T&R Frank ... View more

Hi, we have a Domain Integrated Safeword application, which was installed on our Domain Controller. Safeword requests were send over the Radius Port to the NPS server, and from there over Port 5040 to the Safeword application. This works without any problems. Now we would like to integrate the Cisco ISE to the Safeword. Because there is a checkbox "Safeword Server" at the Radius Token Identity Source, I thought that it is possible to communicate direct with the Safeword application, but it is not working. Anyone who already implemented this?? T&R Frank ... View more

Hallo, I did make a fresh installation of LMS 4.0 on a Windows 2008 R2 (SAP1) server. During the installation I had no error message. After installation I wanted to log in to the LMS Console with the "admin" user. The login was successfull but after zhis, I got an 404 error: (see attached file) Funnily enough it works with the "guest" user Does anyone have an idea?? Thanks in advance Frank Error:The requested URL cannot be reached because .... ... View more