Hello, I hope someone answer my question: We have one VPN ASA using Cisco AnyConnect Premium license, users connect with Cisco AnyConnect Client 3.1.08009, now I have to bring one more site up with second ASA and planning to use AnyConnect Plus license and upgrade  AnyConnect client to 4.1. My question “Can users with AnyConnect Client 4.1 access both sites or not “ Thanks. ... View more

I just reboot my both firewalls connected as active/failover mode, some of the devices were not establishing the connection. when I checked the fire wall I notice these connection using same source and destination interface OUTSIDE. UDP OUTSIDE  10.2.11.1:162 OUTSIDE  10.5.100.93:51046, idle 0:00:26, bytes 169852202, flags -   is any one what cause this ... View more

we have pair of nexus 7k with  software version 5.2(9a). I find following  version discrepancy on  openSSH  built into switch and CMP MGMT module. Nexus Switch: SSH-2.0-OpenSSH_5.5 CMP MGMT Module : SSH-2.0-OpenSSH_4.5 I just want to know why this difference , and how can we update CMP module to bring it to OpenSSH 5.5.     thanks   -Shuja   ... View more

Hi experts, We have pair of 6506-E series switches and we would like to upgrade IOS to ver s72033-adventerprisek9_wan-mz.12.2(33)SXJ4 from 122-33.SXJ2 because it best meets our long term requirements. These switches configure as virtual switching system (VSS) with Virtual Switching Supervisor 720-10GE. We need help to determine  best possible strategy to  minimize the downtime.  I took the following notes from cisco documents VSS-SW#copy tftp: disk0: VSS-SW#copy sw1-slot6-disk0: s72033-adventerprisek9_wan-mz.122-33.SXJ4.bin sw2-slot2-disk0: VSS-SW# config t VSS-SW(config)# no boot system VSS-SW(config)# config-register 0x2102 VSS-SW(config)# boot system flash disk0:s72033-adventerprisek9_wan-mz.122-33.SXJ4.bin VSS-SW(config)# end VSS-SW# copy run start VSS-SW# redundancy reload peer VSS-SW# show redundancy <verify peer is back up in STANDBY-COLD state. Confirm the correct IOS is loaded> VSS-SW# redundancy force-switchover <This will reload the active chassis and standby will take over. Confirm the correct IOS is loaded> ... View more

We are using 6506-E in VSS environment with following modules installed. 6506-E Modules Mod Ports Card Type                             Model             Serial No. --- ----- -------------------------------------- ------------------ ----------- 1   4 CEF720 4 port 10-Gigabit Ethernet     WS-X6704-10GE     SAL14491P9Z 2   4 CEF720 4 port 10-Gigabit Ethernet     WS-X6704-10GE     SAL14491PBV 3   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL14480S7S 6   5 Supervisor Engine 720 10GE (Active)   VS-S720-10G       SAL1446ZS0N Mod Sub-Module                 Model             Serial       Hw     Status ---- --------------------------- ------------------ ----------- ------- ------- 1  Centralized Forwarding Card WS-F6700-CFC       SAL1448172S 4.1   Ok 2 Centralized Forwarding Card WS-F6700-CFC       SAL144816Y1 4.1   Ok 3 Centralized Forwarding Card WS-F6700-CFC       SAL144814UE 4.1   Ok 6 Policy Feature Card 3       VS-F6K-PFC3C       SAL14470720 1.1   Ok 6 MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1446001V 5.1   Ok Now we are running out of ports and have one pair of 6509-E which we planning to decommissioned soon, have two WS-X6748-GE-TX modules installed on it which we would like to move to our  6506-E pair. 6509-E modules: Mod Ports Card Type                             Model             Serial No. --- ----- -------------------------------------- ------------------ ----------- 2   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL09169CTY 5   2 Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL09444784 6   2 Supervisor Engine 720 (Hot)           WS-SUP720-3B       SAL09433YXL 7   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL1128UB7B 8   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL1128U8VG Mod Sub-Module                 Model             Serial       Hw     Status ---- --------------------------- ------------------ ----------- ------- ------- 2 Centralized Forwarding Card WS-F6700-CFC       SAL094447Y6 2.0   Ok 5 Policy Feature Card 3      WS-F6K-PFC3B       SAL09423FHA 2.1   Ok 5 MSFC3 Daughterboard         WS-SUP720         SAL09412T4C 2.3   Ok 6 Policy Feature Card 3       WS-F6K-PFC3B       SAL094449L3 2.1   Ok 6 MSFC3 Daughterboard         WS-SUP720         SAL09433YMY 2.3   Ok 7 Centralized Forwarding Card WS-F6700-CFC       SAD1128081W 3.1   Ok 8 Centralized Forwarding Card WS-F6700-CFC       SAD112807WW 3.1   Ok My question is, if my 6506 SUP able take this line card without any issue and keep running in VSS mode, and do I have to do any changes in configuration? and which slot can I installed this card in? sh ver cisco WS-C6506-E (R7000) processor (revision 1.2) with 983008K/65536K bytes of memory. Processor board ID XXXXXXXXXX SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache Last reset from s/w reset 1 Virtual Ethernet interface 102 Gigabit Ethernet interfaces 20 Ten Gigabit Ethernet interfaces 1917K bytes of non-volatile configuration memory. 8192K bytes of packet buffer memory. 65536K bytes of Flash internal SIMM (Sector size 512K). Power: system power total =     5771.64 Watts (137.42 Amps @ 42V) system power used =     1690.92 Watts (40.26 Amps @ 42V) system power available = 4080.72 Watts (97.16 Amps @ 42V) Slot Card-Type         Watts   A @42V Watts   A @42V State State ---- ------------------ ------- ------ ------- ------ ----- ----- 1   WS-X6704-10GE       295.26 7.03   295.26 7.03 on   on 2   WS-X6704-10GE       295.26 7.03   295.26 7.03 on   on 3   WS-X6748-GE-TX     325.50 7.75   325.50 7.75 on   on 5   (Redundant Sup)       -     -     338.10 8.05 -     - 6   VS-S720-10G         338.10 8.05   338.10 8.05 on   on ... View more