Hi;   Yes. I have setup command sets for read-only users. In a Nexus 5K version 7.0(5)N1(1) works, but in a Nexus 9000 C9332PQ version  7.0(3)I7(3).   In the Nexus 5K I can show running config for read-only users (vdc operator) but in Nexus 9000 there is no show running config for the read only user (roles: vdc-operator).   ... View more

The starnge thing is that it appears as available in the FreePBX: Endpoint: cube Not in use 0 of inf OutAuth: cube/cube Aor: cube 0 Contact: cube/sip:cube@40.199.4.67:5060 595cceb131 Avail 2.248 Transport: 0.0.0.0-udp udp 0 0 0.0.0.0:5060 Identify: cube/cube Match: 40.199.4.67/32 Also, when a call is placed, the CUBE receives the call from the Freepbx AND and matches the incoming dial peer. ... View more

Here some debugs:   Jun 15 17:53:49.932: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: OPTIONS sip:cube@40.199.4.67:5060 SIP/2.0 Via: SIP/2.0/UDP 40.199.4.65:5060;rport;branch=z9hG4bKPje69a21c2-e357-40fb-88c7-c41decc4ea6b From: <sip:cube@40.199.4.65>;tag=32927e45-121a-4625-9bad-7c97db7b2fdc To: <sip:cube@40.199.4.67> Contact: <sip:cube@40.199.4.65:5060> Call-ID: 66ecf83d-31fe-4d07-9895-b9f31bb85a4e CSeq: 33179 OPTIONS Max-Forwards: 70 User-Agent: FPBX-14.0.1.24(13.18.4) Content-Length: 0 Jun 15 17:53:49.932: VOICE_REG_POOL: No entry for (cube) found in contact table Jun 15 17:53:49.933: //215/E4B4A88980B9/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 200 OK Via: SIP/2.0/UDP 40.199.4.65:5060;rport;branch=z9hG4bKPje69a21c2-e357-40fb-88c7-c41decc4ea6b From: <sip:cube@40.199.4.65>;tag=32927e45-121a-4625-9bad-7c97db7b2fdc To: <sip:cube@40.199.4.67>;tag=47FD84F-F11 Date: Fri, 15 Jun 2018 13:53:49 GMT Call-ID: 66ecf83d-31fe-4d07-9895-b9f31bb85a4e Server: Cisco-SIPGateway/IOS-15.5.3.S4b CSeq: 33179 OPTIONS Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER Allow-Events: telephone-event Accept: application/sdp Supported: 100rel,timer,resource-priority,replaces,sdp-anat Content-Type: application/sdp Content-Length: 369 v=0 o=CiscoSystemsSIP-GW-UserAgent 3879 3482 IN IP4 40.199.4.67 s=SIP Call c=IN IP4 40.199.4.67 t=0 0 m=audio 0 RTP/AVP 18 0 8 9 4 2 15 3 c=IN IP4 40.199.4.67 m=image 0 udptl t38 c=IN IP4 40.199.4.67 a=T38FaxVersion:0 a=T38MaxBitRate:9600 a=T38FaxRateManagement:transferredTCF a=T38FaxMaxBuffer:200 a=T38FaxMaxDatagram:320 a=T38FaxUdpEC:t38UDPRedundancy       Regards,  ... View more

Hello;   Looks better but I think still not registered, correct me if Im wrong:   SPC02TCa-Backup_SBC_CUBE#show sip-ua register status Line peer expires(sec) reg survival P-Associ-URI ================================ ========== ============ === ======== ============ cube -1 149 no normal ... View more

Here you go:   SPC02TCa-Backup_SBC_CUBE#show run | s sip-ua sip-ua credentials username cube password 7 105D081702181F0A5D realm na.am.lilly.com authentication username cube password 7 00171208035406075E retry invite 3 retry response 3 retry bye 3 retry cancel 3 retry register 10 timers trying 1000 sip-server ipv4:40.199.4.65 ... View more

Hello;     I get the following:   Registrar is not configured ... View more

Hello and thanks for your reply;      How to check if registration is successful on the CUBE?   Regards,  ... View more

Hi Aeby and thanks for your reply;       What about the Cisco side?   I have the following configured: The ip address of the FreePBX is  10.199.4.65   sip-ua credentials username cube password 7 105D081702181F0A5D realm na.am.lilly.com authentication username cube password 7 00171208035406075E retry invite 3 retry response 3 retry bye 3 retry cancel 3 retry register 10 timers trying 1000 registrar ipv4:10.199.4.65 expires 3600 sip-server ipv4:10.199.4.65 ! voice service voip ip address trusted list ipv4 10.199.4.65 mode border-element allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip supplementary-service h450.12 no supplementary-service sip moved-temporarily no supplementary-service sip refer no supplementary-service sip handle-replaces redirect ip2ip signaling forward unconditional fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw sip bind control source-interface GigabitEthernet0/0/1 bind media source-interface GigabitEthernet0/0/1 min-se 86400 session-expires 86400 options-ping 60 midcall-signaling block midcall-signaling preserve-codec early-offer forced call-route url g729 annexb-all ! ! voice class uri 2 sip host 10.199.4.65 voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw codec preference 4 g722-64 ... View more

Ok. Basically its just to copy/paste the damaged siwtch config into the new one. Do you recommend to configure first and then reconnect all the interfaces (vPC and FEX up-links)? Thanks. ... View more

Excellent. Which should be those few commands? Thanks again. Regards, ... View more

Hello Reza;      Will the new switch accept the FEX's interfaces configuration by just copy/paste? Thanks for your great support. Regards,  ... View more