Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Aaron Wilson
Online
Contributor
20+ years of unified communications and collaboration, as well as core network technologies like SDWAN and DDI.
Recent Badges
Awards
Recent Badges
See all
5 Accepted Solution
100 Helpful Vote
CCP Member
1 Accepted Solution
30 Helpful Vote
10 Helpful Vote
1 Helpful Vote
50 Replies
20 Replies
10 Replies
Stats
Member since ‎05-02-2014
335
Posts
48
Helpful
6
Solutions

Re: Webex Employee's Favorite Feature of The Month: Noise Removal

Created by in Announcements
03-02-2021
03-02-2021
Using noise reduction to remove all the dog barking my dogs have decided to do lately. Worms great, ...

Re: Room Kit Plus keeps post-pending CUCM URL too all calls (causing external calls to fail)

Created by in TelePresence and Video Infrastructure
03-16-2019
03-16-2019
Did you only compare the codec config, or the CUCM config as well? Codec config will not yield anyth...

Re: DX80 not seen by new PC as a monitor

Created by in TelePresence and Video Infrastructure
03-16-2019
03-16-2019
Missed the other replies, ignore this ;)

Re: Expressway-C and Expressway-E Cluster - Across multiple Data Centers

Created by in TelePresence and Video Infrastructure
03-16-2019
03-16-2019
This is an interesting design. You'd have to be careful that a call would not go DC1>>DC2>>DC3, this...

Re: Cisco SX80 Codec Integration with CUCM 11.5.1 and VCS 8.10 and WebEX CMR

Created by in TelePresence and Video Infrastructure
03-16-2019
03-16-2019
I personally would not go below 1.5M per call. I have done some calls at 1.1M (1152kbps), but its no...

Re: Jabber Config File Generator

Created by in Collaboration, Voice and Video Documents
01-16-2019
01-16-2019
Is the Jabber XML configurator ever going to get updated for 12.x? -Aaron

Re: Spark Room Kit Plus shows 'none' as status in CUCM, but it IS registered

Created by in IP Telephony and Phones
12-19-2018
12-19-2018
@notinstock wrote: I had the same problem.... Did not have Call Manager service Running on my Publis...

Re: Spark Room Kit Plus shows 'none' as status in CUCM, but it IS registered

Created by in IP Telephony and Phones
02-26-2018
02-26-2018
Thank you for the info!

Re: Spark Room Kit Plus shows 'none' as status in CUCM, but it IS registered

Created by in IP Telephony and Phones
02-24-2018
02-24-2018
Running into the same issue. The device pack instructions mention restarting CallManager on the pub,...

I have seen some other bugs

Created by in TelePresence and Video Infrastructure
03-16-2017
03-16-2017
I have seen some other bugs which were introduced in a firmware version and until resolved by Cisco ...

How exactly did you configure

Created by in TelePresence and Video Infrastructure
03-16-2017
03-16-2017
How exactly did you configure TMS to reference CUCM? Do you have CUCM nodes added to TMS? Or were yo...

Did you try upgrading from

Created by in TelePresence and Video Infrastructure
03-16-2017
03-16-2017
Did you try upgrading from working 7.3.6 directly to 8.3.1?

So strange, I just refreshed

Created by in TelePresence and Video Infrastructure
03-16-2017
03-16-2017
So strange, I just refreshed my clusters the other week and ALL files were .cer. Everything uploaded...

I just updated a bunch of

Created by in TelePresence and Video Infrastructure
03-15-2017
03-15-2017
I just updated a bunch of certificates on my 8.8.3 VCS's. After I generated the CSR, I was provided ...

Macs like to require HDCP

Created by in TelePresence and Video Infrastructure
03-09-2017
03-09-2017
Macs like to require HDCP even though you are not "sending HDCP content". Also, VGA>>DVI uses entire...
Public Statistics
Date Registered ‎05-02-2014 08:49 AM
Date Last Visited ‎03-03-2021 01:21 PM
Total Messages Posted 335
Total Helpful Votes Received 48