About ian.m.covington

CML-P 2.1 user administration changes · 12-29-2020

I couldn't find anything specific in the documentation, but does CML 2.1 with a personal license no longer allow additional users? I had the ability to create additional users in 2.0, which was nice just for the purpose of separating admin and user r...

ian.m.covington · 09-01-2020

Has anyone had any luck in using custom images to create nodes and definitions in CML 2? I am attempting to create a PacketFence node from a qcow2 image that I converted from OVA, but I get the 'unable to clone image' error when I try to start it. Th...

ian.m.covington · 06-12-2018

I'm having trouble configuring secure mac addresses on a Cisco 891W (CISCO891W-AGN-A-K9). Here is the CLI in/out: (config)#mac-address-table secure sticky f6 Need to enable dynamic port security on the port first before enabling the sticky address (c...

ian.m.covington · 01-05-2018

All, For buildings without fiber, a T1 solution was used to provide connectivity using the ISR Gen 1 & 2. The solution bridged Ethernet sub-interfaces to serial sub-interfaces. Each Serial sub-interface had a Frame Relay DLCI assigned to it. This a...

ian.m.covington · 10-13-2016

Does anyone know the trick to having a Tcl script run a show command containing a "pipe" option? The following example does not work as is, but the show command works fine without a pipe option. I'd like to be able to extract an acl exactly as it exi...

ian.m.covington · 12-29-2020

Thanks Martin. Out of curiosity, was that intended to be the case in 2.0 and they missed it, or did they decide to make a change going forward? I think I remember VIRL personal supporting multiple users.

ian.m.covington · 01-09-2018

Looking at the documentation found here: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/wan_frly/configuration/xe-3s/wan-frly-xe-3s-book/wan-frly-eth-ls-xe.html . Would you agree that 'In the direction from Ethernet to Frame Relay: On the Ethernet...

ian.m.covington · 01-05-2018

Thanks Eduardo, I've looked into EVCs using service instances and BDI, unfortunately it is only supported using Ethernet interfaces, and we need to bridge between Ethernet and Serial on the same device. I'm looking into L2VPN with Ethernet/VLAN t...

ian.m.covington · 02-22-2016

It would definitely be reasonable to predict, especially if the attacker had knowledge of how many characters of the previous encrypted key were used for the next key and the limited number of possible character values. For this script to work as is,...

ian.m.covington · 02-21-2016

I came up with a way to get the result I wanted. Here is the solution: ########## action 3.00 cli command "do show clock"action 3.01 gets $_cli_resultaction 3.02 regexp "[0-9][0-9]" "$_cli_result" hoursaction 3.03 cli command "do show clock"action...

Member Since	‎08-31-2014 10:07 PM
Date Last Visited	‎01-01-2021 05:35 AM
Posts	20
Total Helpful Votes Received	5

User Statistics

User Activity

CML-P 2.1 user administration changes

'Unable to clone image' error when starting a custom node/definition

891W 'mac-address-table secure sticky' partially missing feature

ISR 4000 bridged serial sub-interface support removed - need workaround

Need Tcl script to run show command with piped inc/exc/redir options

Re: CML-P 2.1 user administration changes

Re: ISR 4000 serial sub-interface support removed - need workaround

Re: ISR 4000 serial sub-interface support removed - need workaround

It would definitely be

I came up with a way to get