Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About andtoth
Stats
Member since
10-08-2010
264
Posts
228
Helpful
34
Solutions
11-30-2012
12:25 PM
Hi Alex, The command is hidden, as far as I know because it is not supported and replaced by "table-maps". If you press enter after "platform qos map" it will say incomplete command, so it's still there but hidden. You could use the "table-map" command instead and "show table-map" to verify the config. Details in the guide below: http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/15.0SY/configuration/guide/qos_global_and_if.html Best regards, Andras
... View more
06-25-2012
05:41 AM
Hi James, Output drops might be due to real packet drops. Please check with the 'show platform port-asic stats drop gi ' command to see if drops are seen in hardware. Please also refer to the following post: https://supportforums.cisco.com/thread/2079859 Best regards, Andras
... View more
06-01-2012
03:38 PM
Hi Caroline, Netflow does not work on IPBase in 12.2(50)SY versions. You either need IPServices or higher or run 15.0(1)SY release or later. Best regards, Andras
... View more
05-30-2012
02:28 AM
No problem, glad it works now. Please rate helpful posts. Best regards, Andras
... View more
05-30-2012
01:48 AM
Hi Louisa, Once you enable ip routing, the switch relies on the IP routing table (sh ip route) instead of the ip default-gateway command. This might break your management access if you're accessing the switch from another non directly connected network. Make sure you configure a default route towards your gateway, which will most likely be the following command for you: ip route 0.0.0.0 0.0.0.0 10.112.47.253 Best regards, Andras
... View more
05-30-2012
12:48 AM
Hi Louisa, There are 2 important things to be done: - Make sure you reload the switch after changing the SDM template. - Enable 'ip routing' in global config mode so routing can work. There's no need to configure static routes on the switch, because it knows about both networks already as they're directly attached. If this does not help, try pinging the switch int Vlan address (gateway IP) from the connected devices to see if they are reachable. Best regards, Andras
... View more
05-29-2012
02:53 AM
Hi Louisa, 0 routed interface is normal. The 2960S can route for SVIs, but not for "no switchport" (routed) ports. http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/software/release/12.2_55_se/configuration/guide/swipstatrout.html In the blog post you mention, the output is from a 2960 not from a 2960S, and the value of 8 is invalid in that case, caused by a cosmetic software defect. Best regards, Andras
... View more
04-26-2012
01:17 PM
Hi Pichet, The dot1q and dot1ad features cannot co-exist in the same chassis, so these are mutually exclusive. In other words, once you enable dot1ad globally, dot1q trunk ports will not receive traffic, this is an expected behavior. You can use a L3 routed port instead of switchport to communicate with non-dot1ad devices. Thanks, Andras
... View more
01-19-2012
05:35 AM
As I mentioned already, this will not be fixed in 12.1E because it's not developed anymore. Andras
... View more
01-19-2012
05:14 AM
Hi Marc, Yes, depending on which version you are currently running. Please read through the previous messages where we discussed which software defects are related and in which versions this is fixed. Best regards, Andras
... View more
09-22-2011
06:28 AM
Hi Adrien, Probably the STP BPDU packets are not getting through the VPLS. Please see the following link for more information about STP Loopguard and explanation how it's working: http://www.cisco.com/en/US/tech/tk389/tk621/technologies_tech_note09186a0080094640.shtml Loop Guard kicks in when there's a loss of hearing BPDU packets from the other side. Best regards, Andras
... View more
09-06-2011
08:29 AM
Hi, Did you try upgrading to latest IOS version? Make sure links are not unidirectional with UDLD. Check if control-plane policing is blocking CDP. Andras
... View more
09-06-2011
08:26 AM
The command is mls qos channel-consistency. http://www.cisco.com/en/US/docs/ios/qos/command/reference/qos_m2.html#wp1041289 Andras
... View more
09-06-2011
08:16 AM
Hi, The 10G license is considered a paper license, therefore it does not require further isnstallation on the switch. Andras
... View more
09-05-2011
05:36 PM
Hi Stuart, If you are planning to use link bonding (link aggregation) on the host, consider using Etherchannel, otherwise MAC flapping might occur leading to high CPU usage, unknown unicast flooding, or even a L2 loop might form which can melt down your network. If link bonding (etherchannel) is configured on only one side of a link, it's considered a misconfiguration, therefore enable it on both sides. Best regards, Andras
... View more
11-30-2012
Hi Alex,The command is hidden, as far as I know because it is not
supported and replaced by "table-m...
06-25-2012
Hi James,Output drops might be due to real packet drops. Please check
with the 'show platform port-a...
06-01-2012
Hi Caroline,Netflow does not work on IPBase in 12.2(50)SY versions. You
either need IPServices or hi...
05-30-2012
Hi Louisa,Once you enable ip routing, the switch relies on the IP
routing table (sh ip route) instea...
05-30-2012
Hi Louisa,There are 2 important things to be done:- Make sure you reload
the switch after changing t...
05-29-2012
Hi Louisa,0 routed interface is normal. The 2960S can route for SVIs,
but not for "no switchport" (r...
04-26-2012
Hi Pichet,The dot1q and dot1ad features cannot co-exist in the same
chassis, so these are mutually e...
01-19-2012
As I mentioned already, this will not be fixed in 12.1E because it's not
developed anymore.Andras
01-19-2012
Hi Marc,Yes, depending on which version you are currently running.
Please read through the previous ...
09-22-2011
Hi Adrien,Probably the STP BPDU packets are not getting through the
VPLS. Please see the following l...
09-06-2011
Hi,Did you try upgrading to latest IOS version?Make sure links are not
unidirectional with UDLD.Chec...
09-06-2011
The command is mls qos
channel-consistency.http://www.cisco.com/en/US/docs/ios/qos/command/reference...
09-06-2011
Hi,The 10G license is considered a paper license, therefore it does not
require further isnstallatio...
Public Statistics
| Date Registered | 10-08-2010 07:55 AM |
| Date Last Visited | 04-16-2018 02:52 AM |
| Total Messages Posted | 264 |
| Total Helpful Votes Received | 228 |
Helpful Votes From
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 3 | |
| 10 |
.jpg "Hall of Fame Master"){kind=icon}
