About MINNSD

MINNSD · 09-03-2015

Bit of a strange one .My customer has a mixture of 6941 , 7975 ip phones and analogue ports off a vg224They dial a number that connects to a fxo port holding a BOGEN TAMB2 which in turn hands this off to an amp for paging people around the facilit...

MINNSD · 08-10-2014

isdn bchan-number-order ascending round-robin is applied but not workingios c3825-spservicesk9-mz.124-21.binrelevant config controller E1 0/3/0 framing NO-CRC4 pri-group timeslots 1-31 interface Serial0/3/0:15 no ip address encapsulation hdlc no log...

MINNSD · 01-21-2014

CISCO WLC 5500 customer trying to fit new AP but getting message "capwap_image_proc: problem extracting tar file". this only happens on AIR-LAP1242AG-N-K9 . checking the controller cli "show ap bundle primary" the c1240 image is missing , however s...

MINNSD · 11-28-2013

cucm 8.6users are logged in ok , however the auto logout is set to 12hrs ( correctly configured on service aprameters etc)when i check the devices I can see on the phone page it seems to be logged out but the cust is still logged in .. this is cluste...

MINNSD · 08-21-2013

I am getting reoccurring alm "nodemgr nscd service died" version oe7371-4.1.5fI am aware of a bug id CSCtn31868 but that is only supposed to affect versions 4.1.7 ( and above) or 4.2.x or 4.3.x or 4.4.x any suggestions ?

MINNSD · 08-15-2014

This is an h323 gateway , channel selection is done on mgcp gateways . the default is ascending on this gateway , i/c calls are descending . With no config ( see original input) o/g calls are using ch1 > 31 and i/c calls use b channels 31 > 1

MINNSD · 08-11-2014

thanks for the reply but without this command it selects the order 1-31 , with the order in any combination it still selects ch1 if free every time ie ascending/ descending , not applied or round robinthe i/c calls from the telco come in in the or...

MINNSD · 01-21-2014

Thanks , I think really what I am asking is why is there an image in the secondary ap bundle and not the primary ap bundle , is that from the backup boot image 6.90.199.4 ?. I am having problems finding any information on ap bundles and how they a...

MINNSD · 11-28-2013

It is a customer of ours, cm was installed 417 days ago, as it is auto logout it is possible the customer has just noticed this as an issue .. we can log the customers phone out using the logout button on the device page of cm . I have checked the...

MINNSD · 11-04-2011

That worked a treat Brent. Had customer downgrade and it worked fine.. As it happens we had a UCCX in as well for another customer and the update button was missing when they went to make changes.. Same reason.. ~~~ thanks for all the replies, al...

Member Since	‎09-24-2003 09:10 AM
Date Last Visited	‎10-09-2017 11:32 AM
Posts	18

User Statistics

User Activity

volume problems using a BOGEN TAMB2 on cetain phones

isdn bchan-number-order ascending round-robin is applied but not working

New AP unable to download c1240 image from controller 5500

extn mobility phones do not auto logout after fixed time

Reoccurring alarm "nodemgr nscd service died"

This is an h323 gateway ,

thanks for the reply but

New AP unable to download c1240 image from controller 5500

Re:extn mobility phones do not auto logout after fixed time

Unable to make changes to phones.