Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Syed Siraj Uddin
09-10-2019
Stats
Member since
11-06-2012
33
Posts
18
Helpful
5
Solutions
07-12-2016
11:35 PM
which serial console client you were using while accessing the routers?
... View more
07-12-2016
05:11 AM
do you have access to cli once the router reboots?
if yes, check if the following command is present in the configuration
no service password-recovery to remove the command use
service password-recovery
if not you are not using the break sequence correctly to gain access to ROMMON mode.
... View more
07-12-2016
04:03 AM
Hi,
why do you have 2 default routes? Please make sure you have RDP enable on host 10.1.10.16.
other than that the configuration looks fine.
... View more
03-17-2016
04:54 AM
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/68131-cat-multicast-prob.html
refer to the attach link for multicast configuration for a setup similar to yours.
... View more
03-17-2016
04:45 AM
Only when you have an EtherSwitch module (eg, NM-16ESW: One 16-port 10/100 EtherSwitch Network Module ) and a proper IOS image.
... View more
03-17-2016
04:22 AM
Hello,
I think the setup you are trying to build will not work,
because you are trying to connect an FTTH modem to a gigabit Ethernet switch.
You will need an OLT switch to make your setup work generally used by service providers..
... View more
12-22-2013
01:39 PM
Aamer did you manage to make this work ;) ? Sent from Cisco Technical Support iPhone App
... View more
08-25-2013
05:07 AM
Hi, This is smply a routing issue. ping vrf ABC 192.10.2.2 <-- Using this command your source IP will be the IP of exit interface throught which the route for host is learned (in your case 192.10.2.2) If you are learning the route for 192.10.2.2 from interface e0/0 and the ip of interaface e0/0 is 1.1.1.1 ping vrf ABC 192.10.2.2 = ping vrf ABC 192.10.2.2 source 1.1.1.1 In your case you dont have proper routing between 192.10.2.2 & 1.1.1.1
... View more
Created by
Syed Siraj Uddin
in Switching
in Switching
02-06-2013
04:12 AM
02-06-2013
04:12 AM
Hi, is this a flat L2 network between HO & Branch?
... View more
02-06-2013
12:52 AM
Hi Ravi, your prefix list seems to be fine but you will need a distribute list to filter out the default router being installed in the routing table. Sample config: router ospf 1 distribute-list prefix DEF_BLK in HTH
... View more
Created by
Syed Siraj Uddin
in Routing
in Routing
02-05-2013
09:27 PM
02-05-2013
09:27 PM
Hi Evan, Please post the entire configuratoin. thank you.
... View more
02-04-2013
09:52 PM
So, when we have Internet issues in a site, the plans are to use the WAN conenction as a backup. This only seems to work at the moment when we manually change the default route on our LAN switch to point to the WAN rather than the Internet provider. This isn't ideal since it only works when the primary Internet connection is down. it can be done using ip sla. I would like to use the secondary Internet connection not only as a backup for failure, but also for services to be reachable via two Internet connections, like a website. At this point, when we create a nat on a remote firewall, the traffic comes in but cannot go back because it is routed out the local Internet. its almost imposible to host services as the pulic ip subnet you have from one provider will not work on the other link .. when the link is down HTH.
... View more
Created by
Syed Siraj Uddin
in Routing
in Routing
02-04-2013
09:33 PM
02-04-2013
09:33 PM
Hi, you will have to create a nat pool to get the desired result. sample configuration. ip nat pool Net31 31.210.x.x 31.210.x.x netmask 255.255.255.240 ip nat inside source list 1 pool Net31 overload access-list 1 permit 192.168.1.0 0.0.0.255 HTH
... View more
Created by
Syed Siraj Uddin
in Routing
in Routing
02-04-2013
09:21 PM
02-04-2013
09:21 PM
Hi, Edit your ACL 106 to deny traffic between your Public IP (IPsec Peer) and remote end IPSEc Peer. hopefully this will solve your problem. HTH.
... View more
07-12-2016
do you have access to cli once the router reboots? if yes, check if the
following command is present...
07-12-2016
Hi, why do you have 2 default routes? Please make sure you have RDP
enable on host 10.1.10.16. other...
03-17-2016
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/68131-cat-multicast...
03-17-2016
Only when you have an EtherSwitch module (eg,NM-16ESW: One 16-port
10/100 EtherSwitch Network Module...
03-17-2016
Hello, I think the setup you are trying to build will not work, because
you are trying to connect an...
08-25-2013
Hi,This is smply a routing issue.ping vrf ABC 192.10.2.2 <-- Using this
command your source IP will ...
Created by
Syed Siraj Uddin
in Switching
02-06-2013
02-06-2013
Hi, is this a flat L2 network between HO & Branch?
02-06-2013
Hi Ravi,your prefix list seems to be finebut you will need a distribute
list to filter out the defau...
Created by
Syed Siraj Uddin
in Routing
02-05-2013
02-05-2013
Hi Evan,Please post the entire configuratoin.thank you.
02-04-2013
So, when we have Internet issues in a site, the plans are to use the WAN
conenction as a backup. Thi...
02-04-2013
Hi,you will have to create a nat pool to get the desired result.sample
configuration.ip nat pool Net...
Created by
Syed Siraj Uddin
in Routing
02-04-2013
02-04-2013
Hi, Edit your ACL 106 to deny traffic between your Public IP (IPsec
Peer) and remote end IPSEc Peer....
Public Statistics
| Date Registered | 11-06-2012 09:16 AM |
| Date Last Visited | 09-10-2019 10:51 PM |
| Total Messages Posted | 33 |
| Total Helpful Votes Received | 18 |
Helpful Votes From
| User | Helpful Count |
|---|---|
| 4 | |
| 5 | |
| 3 | |
| 3 | |
| 1 |
