Hi Graham   Thanks for your time and assistance, it was very helpful.   I've tested it in our staging environment and it works. We're going to put this into production the next few days.    /T ... View more

Hi Graham   Pritty much the same as:   ! dspfarm profile 1 transcode codec g711alaw codec g711ulaw codec g722-64 maximum sessions 12 associate application CUBE ! voice class e164-pattern-map 100 #DNs for those applications ! voice class codec 2 codec preference 1 g711ulaw ! dial-peer voice 5555555 voip voice class codec 2 voice class e164-pattern-map 100 #rest of dial-peer have been omittet     But this doesnt give exclusive right for that particular dial-peer to that transcoding resource, does it? I belive it gives anything access to that resource.   /T ... View more

Hi Graham   How do i give only one dial-peer access to transcoding?   /Tony ... View more

Hi Graham   Thats good news, in partial at least.   We're using UCCX 11.5.1 so we shouldnt be affected by that bug, should we? I dont see any fixed releases though :(   We're using (i'm guessing here) 50+ applications so making dial-peers for all those would be a pain to setup and maintain.   I've tried using a seperate MRGL that has access to the transcoder (nothing else has that access to that MRGL,  and that MRGL has a only that transcoder enabled) and assigned it to the Triggers. There are no unallocated MTPs on CUCM.   /T   ... View more

Hi Ayodeji   As it registers in CUCM i assume i have it correctly configured: ! voice-card 0 dspfarm dsp services dspfarm ! ! sccp local GigabitEthernet0/0 sccp ccm xx.xx.xx.xx identifier 1 version 7.0 sccp ccm xx.xx.xx.xx identifier 2 version 7.0 sccp ccm xx.xx.xx.xx identifier 3 version 7.0 sccp ! sccp ccm group 1 associate ccm 1 priority 1 associate ccm 2 priority 2 associate ccm 3 priority 3 associate profile 1 register XCODE_ulaw keepalive retries 1 keepalive timeout 10 switchover method immediate switchback method immediate ! ccm-manager config server xx.xx.xx.x ccm-manager sccp local GigabitEthernet0/0 ccm-manager sccp ! dspfarm profile 1 transcode codec g711alaw codec g711ulaw codec g722-64 maximum sessions 12 associate application SCCP !     Our TSP sends G711a only on this SIP trunk (its an staging environment so i kan play around a lot). But i dont see any transcoding being done:   CUBE#show dspfarm dsp active SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED Total number of DSPFARM DSP channel(s) 0 CUBE#show call active voice compact <callID> A/O FAX T<sec> Codec type Peer Address IP R<ip>:<udp> VRF Total call-legs: 2 3772610 ANS T4 g711alaw VOIP P+4792xxxxxx 148.xxx.xxx.xxx:10344 NA 3772611 ORG T4 g711alaw VOIP P073xxxxxxx 10.xxx.xxxx.xxx:24744 NA     ... View more

Hi Chris   I must have overcomplicated things, because LTI was quick to configure (i did it in an staging environment).   The traffic flow with LTI is easy to figure out. Would SCCP registered xcode differ much? Would the load on the resources on CUBE differ?   It is only for the UCCX we need transcoding.   /T ... View more

Hi Slavik   A reinstall did it. I have no idea why. I noticed that the first time you log in through CLI it gives a warning that you might have to restart the "service manager" just to get the services up and running and this is a known bug... The service was restarted several times in fact and it took "forever" to get every service back up running. 30 minutes or more.   Thanks for your assistance, Slavik ... View more

Hi   Here it is: https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/install/11_5_1/cucm_b_installation-guide-cucm-imp-1151/cucm_b_installation-guide-cucm-imp-1151_chapter_010.html?bookSearch=true   --snip-- DNS requirements If you are using DNS in your deployment, note the following requirements: Mixed-mode DNS deployments not supported—Cisco does not support mixed-mode deployments. Both Cisco Unified Communications Manager (Unified Communications Manager) and IM and Presence must either use or not use DNS. --snip--   And Cisco recommends NOT using DNS in CUCM, therefore we have not used DNS on the CUCM.    /T ... View more

Hi   Since CUCM is not using DNS then the install guide says i shouldnt be using DNS on the IMP either.   But i'm thinking a fresh start, a reinstall, would be the way to go.   /T ... View more

Hi Slavik   I have this error message: The IM Address Scheme is currently not set to Directory URI and as a result the domains listed below are not in use. To change this setting, please go to the following page,  AdvancedPresence Settings.   But since i'm not able to stop the Precense Enginge i'm not able to change it.    /T ... View more

Hi Slavik   You might be right but i can't stop the engine, neither though GUI nor CLI. The other services : Cisco SIP, Proxy, Cisco XCP Router, Cisco Sync Agent and Cisco Client Profile Agent stops as expected.   There were a Domain in the "system domain" section, so i added a domain in the "admin section" but it didnt do anything so i'm rebooting the server now.   /T ... View more

Hi Slavik   I agree, lets get the basics confimed. 1. Yes they are on the same subnet, aka no firewall between CUCM and IMP. 2. Neither CUCM nor IMP is configured with DNS. 3. Yes, its there in the Presence Redundancy Group.   BTW: I am able to sync users from CUCM to IMP.   /T ... View more

Hi Slavik   I've just installed it, so everything would be new :) The troubleshooter only has one warning: Verify that the Cisco Presence Engine service is running. The Cisco Presence Engine service is currently not running. To start the Cisco Presence Engine service, use the Serviceability application. (fix)   Restarting it via CLI or GUI gives same out put. Rebooting the whole server does not help either.   /T ... View more