Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About r-reed
Stats
Member since
04-04-2001
59
Posts
0
Helpful
0
Solutions
Created by
r-reed
in Cisco CLI Analyzer
in Cisco CLI Analyzer
07-19-2017
11:25 AM
07-19-2017
11:25 AM
Cisco CLI Analyzer Version 3.4.0 gives me the following:
From the uploaded show tech or show run-config, controller is running 8.0.140.0 which is not a recommended code for production use. For TAC recommended AireOS code refer http://www.cisco.com/c/en/us/support/docs/wireless/wireless-lan-controller-software/200046-TAC-Recommended-AireOS.html
The referenced page recommends 8.0.140.0.
... View more
Labels:
07-20-2011
08:05 PM
CLI can be done a little easier with: show access-list | in inactive to only show the lines containing "inactive"
... View more
07-10-2011
10:51 AM
Goran, The ASA5505 does not support spanning tree. Your unmanaged switches most likely do not support spanning tree. With both cables plugged into the ASA you most likely have a loop configured.
... View more
07-06-2011
02:21 PM
This link will show you how to load an image from the monitor mode you appear to be in. Hope it helps. http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_tech_note09186a0080094a5d.shtml#faulty
... View more
06-29-2011
07:33 PM
Your log show that this is being blocked on inside. Maybe 123.123.123.123 is infected?
... View more
06-29-2011
07:13 PM
Patrick, The most common reason for slow transfers is duplex mismatch. Check ASA ports and switch/server ports to ensure that every point to point connection matches on duplex. Auto - Auto is fine, Full - Full is fine but Auto - Full will cause this issue.
... View more
11-15-2006
01:59 PM
While auditing a client (using Kismet) I found that some of their Cisco APs have a <info> field in beacon packets. I'm trying to figure out where the data for this field is entered in the configuration. I do not have access to the configurations. The data is not the SSID but in some cases is similar. Any help is appreciated. Thanks
... View more
Created by
r-reed
in Wireless Security and Network Management
in Wireless Security and Network Management
11-18-2005
07:42 AM
11-18-2005
07:42 AM
I too am seeing the same issue on multiple 1100s
... View more
Created by
r-reed
in Wireless Security and Network Management
in Wireless Security and Network Management
11-18-2005
06:58 AM
11-18-2005
06:58 AM
I'm getting a lot of these messages in my logs on an 1121G AP. We are doing 802.1x with WPA. Can someone tell me what this means? Nov 17 18:52:47.967: *** TKIP Replay[ucast q 4]: TA=000c.f14c.9a6f, RSC=0x4A113, TSC=0x4A112 Nov 17 23:27:09.514: *** TKIP Replay[ucast q 4]: TA=000c.f14c.9a6f, RSC=0x634BB, TSC=0x634BA Thanks
... View more
06-01-2005
07:26 AM
No I just want to put up IIS in order to support a second product on the box. I have a large server for LMS and would like to put a second applicaton on it that needs IIS.
... View more
05-17-2005
10:42 AM
I have also found that $ is a problem in baseline templates if you try to deploy (LMS 2.5)
... View more
05-09-2005
11:40 AM
I'm running LMS2.5 on 2003 and have both etc/hosts and DNS resolution working by default (meaning I didn't do anything to make it work).
... View more
05-03-2005
08:20 AM
I have set the memory requirements for the image to 2MB for both flash and DRAM. When I create the job it shows 2.88MB flash and 8MB DRAM. This is the error I get when submitting a job: Warning - SWIM1069:Feature subset of the running image cannot be determined. Select a different image. Catastrophic - SWIM1111:The available free space is not enough for upgrading this type of image. Select a different image or free up some space. Update the inventory and retry the operation.
... View more
04-25-2005
10:06 AM
Trying to use RME 4.0 to distribute IOS to 805 router. The issue is flash space. RME says not enough memory. Is there a way around this because I know I can update manually using TFTP. If I can do it manually then RME should be able to do it. I just don't want to have to do 300 routers by hand.
... View more
Labels:
07-19-2017
Cisco CLI Analyzer Version 3.4.0 gives me the following: From the
uploaded show tech or show run-con...
07-20-2011
CLI can be done a little easier with:show access-list | in inactiveto
only show the lines containing...
07-10-2011
Goran,The ASA5505 does not support spanning tree. Your unmanaged
switches most likely do not support...
07-06-2011
This link will show you how to load an image from the monitor mode you
appear to be in. Hope it
help...
06-29-2011
Patrick,The most common reason for slow transfers is duplex mismatch.
Check ASA ports and switch/ser...
Created by
r-reed
in Unified Communications Infrastructure
01-23-2008
01-23-2008
I have this same issue with a clean install on both servers. Installed
4.2 on primary and integrated...
11-15-2006
While auditing a client (using Kismet) I found that some of their Cisco
APs have a field in beacon ...
Created by
r-reed
in Wireless Security and Network Management
11-18-2005
11-18-2005
I too am seeing the same issue on multiple 1100s
11-18-2005
I'm getting a lot of these messages in my logs on an 1121G AP. We are
doing 802.1x with WPA. Can som...
06-01-2005
No I just want to put up IIS in order to support a second product on the
box. I have a large server ...
05-17-2005
I have also found that $ is a problem in baseline templates if you try
to deploy (LMS 2.5)
05-09-2005
I'm running LMS2.5 on 2003 and have both etc/hosts and DNS resolution
working by default (meaning I ...
Public Statistics
| Date Registered | 04-04-2001 06:14 AM |
| Date Last Visited | 10-21-2017 04:57 PM |
| Total Messages Posted | 59 |
