Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Simon Ko
06-26-2019
Simon Ko
Member since
07-16-2013
Beginner
Created by
Simon Ko
in Wireless Security and Network Management
in Wireless Security and Network Management
05-16-2019
07:34 AM
05-16-2019
07:34 AM
VIrtual address of 1.1.1.1 has been retired. It is being used by DNS provider. You change your virtual address to 192.0.2.1 I believe.
... View more
05-07-2019
03:37 PM
Now I understand your concern. answer is , your isp router has to point to your wan IP address for /26 net. ip route x.x.x.x 255.255.255.192 your-Isr-wan-address on your lan interface int gi0/0/1 desc LAN interface ip address y.y.y.y 255.255.255.192 no shut and on global Ip route 0.0.0.0 0.0.0.0 your-isp-wan-address on firewall ip route 0.0.0. 0.0.0.0 your-Isr-lan-address just make sure your isp router has a static route for /26 pointing to your Isr-wan-address
... View more
05-07-2019
03:33 PM
Now I understand your concern. answer is , your isp router has to point to your wan IP address for /26 net. ip route x.x.x.x 255.255.255.192 your-Isr-wan-address on your lan interface int gi0/0/1 desc LAN interface ip address y.y.y.y 255.255.255.192 no shut and on global Ip route 0.0.0.0 0.0.0.0 your-isp-wan-address on firewall ip route 0.0.0. 0.0.0.0 your-Isr-lan-address just make sure your isp router has a static route for /26 pointing to your Isr-wan-address
... View more
05-07-2019
01:51 PM
I think what you are doing is splitting two network on two devices. /30 will go to WAN port and /26 will go to the Firewall. But, if your firewall's external interface has the /26 address configured, you have to use one of /26 address for ISR's LAN interface. If your firewall has dmz configured as /26 address. you can use private address between firewall's external interface and ISR's LAN interface. You just have to point 0.0.0.0 route on firewall to ISR's LAN address and ISR's /26 network point to Firewall's external address. Hope this make sense.
... View more
Created by
Simon Ko
in Physical and Virtual Network Elements
in Physical and Virtual Network Elements
05-07-2019
01:30 PM
05-07-2019
01:30 PM
If pip did install iperf3, it should be in /usr/lib/ directory. Maybe you just need to create a symlink to libiperf.so.0. Maybe it was supposed to be iperf, not iperf3. MIPS has a lite version of guestshell. you can try 'pip install --upgrade iperf3' to see if it will update. Let us know what you found.
... View more
06-14-2019 05:24 AM
Does anyone know if it is possible to upgrade rom-monitors on ISR
devices via vManage? On IOS-XE, up...
06-13-2019 12:53 PM
Really simple,A. OMP's next hop is a site address, not next hop
interface.B. This means, a redistrib...
06-13-2019 12:28 PM
I think only transparent devices can do this.ASA on wire mode and
Riverbed in Fail-to-wire , I belie...
05-24-2019 10:37 AM
I think you are as puzzled as I was about IWAN DNA APIC-EM and SD WAN.
According to "Viptela Integra...
05-16-2019 07:49 AM
I hope I know the answer but here is what I think. Usually, dual MPLS
has a vrrp configured on two r...
Created by
Simon Ko
in Wireless Security and Network Management
05-16-2019 07:34 AM
05-16-2019 07:34 AM
VIrtual address of 1.1.1.1 has been retired.It is being used by DNS
provider.You change your virtual...
05-16-2019 07:28 AM
We are currently pulling all of MPLS connections out of branches,
worldwide.Having two Internet ISP ...
05-14-2019 09:28 AM
As far as I know, vManage uses netconf along with yang device model, to
configure devices.vManage ha...
05-14-2019 09:05 AM
I was hoping that someone would reply to your post.I think you might be
in wrong area.APIC-EM 's nor...
05-13-2019 08:10 AM
Just out of curiosity,if you leave the setting at default setting, does
it apply "default-informatio...
Public Statistics
| Date Registered | 07-16-2013 01:20 PM |
| Date Last Visited | 06-26-2019 12:04 AM |
| Total Messages Posted | 24 |
| Total Helpful Votes Received | 5 |
