Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About christowilson
Stats
Member since
09-30-2013
13
Posts
5
Helpful
0
Solutions
11-10-2013
11:29 AM
Hi Rick, I resolved the issue; first of all I missed to exclude the IP address from translation, secondly and from my customer ends they did a mistake in fonfiguring the ACL of VPN, I resolved by correcting both. many thnkas,
... View more
11-09-2013
10:33 AM
Hi Rick, you right, for many times I applyed sh run, but on last Thursday I was very busy next to this activity, so I forgot to check the NAT translation ACL. any way I do change all required points then I will let you know about the result. thanks,
... View more
11-08-2013
04:55 AM
Hello Rick, I have to exclude the new LAN IP address from the translation, I think I can apply this with in next week. once I changed the configueration I will let you know. currently flushing the SAs does not make any sense, because as you know there is one required step is not done yet. thanks alot for your reply and support. regards, Chris
... View more
11-07-2013
11:48 AM
hello Richard, thanks for your advice, regarding the platforms; my end I used Cisco 2921 ISR router and at the far end (my customer end) they have a JUNI router, also I have applyed translation on my end but I missed to exclude the new LAN far end in the translation. maybe this is the reason. once I changed the NAT access list I will let you know about the result. for the SA I did flush the current SA for many times from my end as well as at the far end, but this did not make any sense. regarding the topology I have an active tunnel to the BGP router, I am not sure about the topology. what happen if there was not a direct connection between the new LAN and the GW? much appreciate your reply and support. best regards,
... View more
11-07-2013
09:06 AM
Hello Bor Marton, this is my mistake in typing. in the real it is 255 and not 244. and from my end when I apply to the new far end LAN I don't have any reply. your advice please. thanks,
... View more
11-07-2013
07:14 AM
hello experts, I have a site-to-site connection, currently I have a stabale connection from my LAN 192.168.1.100 /24 to far end LAN 192.168.55.1 /24, and now I need to add another LAN connetion from my current LAN to anew LAN from the far-end (I want to have an interconnection to multi LAN in the far end). the LAN ip address of the new LAN in the far end is 172.16.1.1 /24 I applyed below policy from both ends but it couldn't work my end: access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.55.0 0.0.0.255 access-list 101 permit ip 192.168.1.0 0.0.0.244 172,16.1.0 0.0.0.225 in the far end I applyed: access-list 102 permit ip 192.168.55.0 0.0.0.255 192.168.1.0 0.0.0.255 access-list 102 permit ip 172.16.1.0 0.0.0.255 192.168.1.0 0.0.0.255 I need yor advice please. thanks,
... View more
Labels:
10-09-2013
01:36 AM
hello experts, Just I have a quesiton, and much apprecicate if you can provide the answer. my question is; what is IP Planning / Operation department in GSM or SP companies? thanks a lot in advance.
... View more
Labels:
Created by
christowilson
in Switching
in Switching
10-07-2013
11:05 AM
10-07-2013
11:05 AM
Hi, I got the solution thanx. but what happen if I disable the SIP tcp / udp services on my router? already I have a CME and I have a site-to-site VPN connection. these services on my router will be affected or not? BTW; can you provide me further information on SIP service? regards,
... View more
Created by
christowilson
in Switching
in Switching
10-07-2013
10:33 AM
10-07-2013
10:33 AM
Hi, %SIP-3-UNSUPPORTED:Unsupported ptime value I decoded this and but there was no helpful information. regards,
... View more
Created by
christowilson
in Switching
in Switching
10-07-2013
10:24 AM
10-07-2013
10:24 AM
hello all, I have an issue in my router and according to the results that I got, I have to open a tac with cisco. please help!! thanks alot,
... View more
Labels:
09-30-2013
02:08 AM
hi expert, I have a cisco router and I use it for internet and VPN currently I have a internet access, but I don't have the VPN connection, I applied the correct configuration for the VPN. regards,
... View more
Labels:
11-10-2013
Hi Rick,I resolved the issue; first of all I missed to exclude the IP
address from translation, seco...
11-09-2013
Hi Rick,you right, for many times I applyed sh run, but on last Thursday
I was very busy next to thi...
11-08-2013
Hello Rick,I have to exclude the new LAN IP address from the
translation, I think I can apply this w...
11-07-2013
hello Richard,thanks for your advice,regarding the platforms; my end I
used Cisco 2921 ISR router an...
11-07-2013
Hello Bor Marton,this is my mistake in typing. in the real it is 255 and
not 244. and from my end wh...
11-07-2013
hello experts,I have a site-to-site connection, currently I have a
stabale connection from my LAN 19...
10-09-2013
hello experts,Just I have a quesiton, and much apprecicate if you can
provide the answer.my question...
10-07-2013
Hi,I got the solution thanx.but what happen if I disable the SIP tcp /
udp services on my router?alr...
10-07-2013
Hi,%SIP-3-UNSUPPORTED:Unsupported ptime valueI decoded this and but
there was no helpful information...
10-07-2013
hello all,I have an issue in my router and according to the results that
I got, I have to open a tac...
Public Statistics
| Date Registered | 09-30-2013 02:04 AM |
| Date Last Visited | 08-18-2017 04:27 AM |
| Total Messages Posted | 13 |
| Total Helpful Votes Received | 5 |
Helpful Votes Given To
