About Qiese Dides

Qiese Dides · 05-07-2016

Introduction This guide is to help trace aborts being generated from your Fibe Channel if you have an upstream switch such as an MDS. Having this information will help pinpoint the exact origin of the abort, which in return will help save time in f...

Qiese Dides · 05-07-2016

Introduction This guide is to help troubleshoot Boot from San issues on your Cisco UCS Blade Server. If you follow these steps before opening a TAC case and have this information ready for the TAC engineer you will be able to save a considerable amou...

Qiese Dides · 04-28-2016

For instructions on downloading the Fusion I/O adapter and how to install please follow the link below; https://supportforums.cisco.com/document/13010356/how-install-fusion-io-adapter-1300mp-or-1600ms-esxi-hosts However, if this is a new installatio...

Qiese Dides · 04-28-2016

How to Install Fusion I/O Adapter (1300MP or 1600MS) to ESXi Hosts The Fusion I/O adapter driver is available for it's specified UCS firmware bundle at Cisco.com. Keep in mind even though the Fusion adapter is a type of storage, it is not a ...

Qiese Dides · 02-02-2016

Below I created a document that gives you a step by step guide on how to create a Service Profile Template. It will also show you step by step on how to create each type of pool that is needed in a template. If anyone is confused please comment and ...

Qiese Dides · 04-25-2020

Hi Amarpal, Please note that the minute you apply a service profile to the blade it will take the BIOS setting that the service profile has configured prior. That is when you can make fine-tuning adjustments to the blades BIOS settings if needed. ...

Qiese Dides · 02-23-2018

Hi Joel, Yes it would be safe to assume this but as I mentioned it's always best to do any major changes in a maintenance window. However, just a heads up when you enable Vlan Port Optimization you will not be able to disable it if your amount of V...

Qiese Dides · 02-22-2018

Also, you most likely will not hit this bug but for anyone else that is reading this thread and is thinking about enabling VLAN port count optimization please be careful for the following bug: https://bst.cloudapps.cisco.com/bugsearch/bug/CSCuf3567...

Qiese Dides · 02-22-2018

Hi Joel, VLAN port count optimization enables mapping the state of multiple VLANs into a single internal state. When you enable the VLAN port count optimization, Cisco UCS Manager logically groups VLANs based on the port VLAN membership. This group...

Qiese Dides · 12-07-2017

Hi KK, As Wes stated the upgrade failed due to a component not being supported in 3.1 you are going from 2.2. This could be something as small as an adapter that your team may not be using but it may need to be decomissioned. The link Wesley provid...

Member Since	‎03-09-2015 05:47 AM
Date Last Visited	‎08-30-2024 06:51 AM
Posts	230
Total Helpful Votes Received	2042

User Statistics

User Activity

Tracing Fibre Channel Aborts on the UCS

Troubleshooting Boot From San Installation

Fusion I/O Adapter not Visbile on ESXI

How to Install Fusion I/O Adapter (1300MP or 1600MS) to ESXi Hosts

Creating UCS Server Profiles with Templates and Pools

Re: BIOS Policy setting "CPU Performance" for M5 Blades- Enterprise or Platform Default?

Re: UCS VLAN Count and ACI

Re: UCS VLAN Count and ACI

Re: UCS VLAN Count and ACI

Re: UCSM Upgrade stuck at 96% from 2.2 (6c) to 3.1 (2e)