Hello everyone , I try to enable wanphy mode on NCS55A2 controller move to preconfigure state. may have any ideas or solutions? RP/0/RP0/CPU0:Nov 12 09:42:41.846 UTC: config[67800]: %MGBL-CONFIG-6-INT_UNRESOLVED : Some of the interface configuration was moved to pre configuration automatically as these interfaces do not exist or could not be mapped to any nodes try both two tips of sfp's SFP-10G-LR-S and SFP-10G-LR-S controller preconfigure wanphy0/0/1/1 wanmode on Output commands RP/0/RP0/CPU0:NCS_55A2#show platform Tue Nov 12 10:01:27.269 UTC Node Type State Config state -------------------------------------------------------------------------------- 0/0/1 NC55-MPA-12T-S OK 0/RP0/CPU0 NCS-55A2-MOD-SE-S(Active) IOS XR RUN NSHUT 0/RP0/NPU0 Slice UP 0/FT0 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT1 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT2 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT3 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT4 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT5 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT6 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT7 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/PM0 NC55-930W-DCFW OPERATIONAL NSHUT 0/PM1 NC55-930W-DCFW FAILED NSHUT RP/0/RP0/CPU0:NCS_55A2#show install active summary Tue Nov 12 10:01:30.558 UTC Active Packages: 9 ncs5500-xr-6.6.25 version=6.6.25 [Boot image] ncs5500-mgbl-3.0.0.0-r6625 ncs5500-li-1.0.0.0-r6625 ncs5500-isis-2.1.0.0-r6625 ncs5500-mcast-2.1.0.0-r6625 ncs5500-ospf-2.0.0.0-r6625 ncs5500-mpls-2.1.0.0-r6625 ncs5500-mpls-te-rsvp-3.1.0.0-r6625 ncs5500-k9sec-3.1.0.0-r6625 RP/0/RP0/CPU0:NCS_55A2#show inventory Tue Nov 12 10:02:33.931 UTC NAME: "0/0", DESCR: "NC55A2 MOD Scale Virtual Line Card" PID: NCS-55A2-MOD-SE-S , VID: V01, SN: FOC231978CS NAME: "0/0/1", DESCR: "NCS5500 12 SFP with 10G OTN, WAN PHY, MacSec, DWDM MPA" PID: NC55-MPA-12T-S , VID: V01, SN: FOC224949QY NAME: "TenGigE0/0/1/0", DESCR: "Cisco SFP+ 10G LR Pluggable Optics Module" PID: SFP-10G-LR-S , VID: V01, SN: FNS231513Z8 NAME: "TenGigE0/0/1/1", DESCR: "Cisco SFP+ 10G LR Pluggable Optics Module" PID: SFP-10G-LR , VID: V02, SN: PH5N901845
... View more