Did you get root cause of this issue ? ... View more

Did you tried different IOS versions ? ... View more

Hi bpgavigan, I am facing the same issue my switch model is 3850 Stack with 3.6.5 IOS. The only solution i have right now is to reboot the stack, did you ever find the solution for your issue ? I am getting the same debug output and Cisco development team is not able to reach on any conclusion yet from last 4 months  ... View more

Hi Peter, Both the shape and police commands restrict the output rate to a maximum kbps value. Importantly, neither mechanism provides a minimum bandwidth guarantee during periods of congestion. Use the bandwidth or priority  command to provide such guarantees. http://www.cisco.com/c/en/us/support/docs/quality-of-service-qos/qos-policing/19645-policevsshape.html#minimumvsmaximum That' why i am using bandwidth command which will provide minimum bandwidth guarantee of 50mb, i am not using police for minimum bandwidth guarantee here i am using police for only to remark the traffic if it will exceed the 49mb ( 45mb with 4mb burst)  As per our service provider we have to mark it with 2 and SP will drop the traffic with IP precedence 2 if it will exceed the 50mb that's why i am remarking it with dscp 0 if it exceeds 50mb.  Priority command will start doping the traffic which exceeds 50mb which i don't want   ... View more

Hello, Its supported now in 9.4  http://www.cisco.com/c/en/us/td/docs/security/asa/asa94/configuration/general/asa-general-cli/route-policy-based.html ... View more

I have ACS 5.3.0.40 patch 6 and i can browse this URL without any credentials than i apply the patch 10 and this url is no longer available and if i try to browse its giving a message "resource not available"  but if i already logged in than i am able to open the URL   Issue is resolved after applying the patch 10 seems a bug     ... View more

I opened the TAC and got the same reply ... View more

ACL, QOS and netflow is configured and ESP packets are not less than 1500 bytes and this router handle ACL, QOS and and netflow in software mean interrupts and as per documents if we enable these services than this router can handle upto T3/E3 traffic ... View more

3845 ... View more

Q. What is the performance of the 3800 series? A. The 3800 Series routers are designed to deliver multiple concurrent services at wire-speed performance of up to T3/E3 rates. The T3/E3 value represents IMIX packet sizes in higher than typical 3800 services configurations. In less service-intense environments, actual WAN throughput will be higher. In light service environments with 64 byte packets, the 3800 series can achieve between 350-500 Kpps http://www.cisco.com/c/en/us/products/collateral/routers/3800-series-integrated-services-routers-isr/prod_qas0900aecd8016a953.html.   =========================================================================== See the performance chart here by Miercom http://www.miercom.com/pdf/reports/20090710.pdf   ===========================================================================   As per following document it can handle 256 Mbs but Numbers are given with 64 byte packet size, IP only, and are only an indication of raw switching performance. These are testing numbers, usually with FE to FE or POS to POS, no services enabled. As you add ACL's, encryption, compression, etc - performance will decline significantly from the given numbers, unless it is a hardware-assisted platform, such as the 7600 or 12000, which process QoS, ACL's, and other features in hardware. https://supportforums.cisco.com/sites/default/files/legacy/8/0/6/18608-routerperformance.pdf It seems router is overloaded with traffic of full size packets and ACL and QOS applied to it   ... View more

Its only 80Mb and as per document its capable to handle more than 200 Mb. Do you think it can related to huge fragments? ... View more