You can contact To Cisco Partner  for the same . Also see 4500 ser controller with 20 licen for wireless device Thanks & Regards Vishal 9310253052 ... View more

Hi, The Phone Proxy features are useful when you are using different subnet in your network Or Specially Useful or recomended when you would like to use your phone over the internet . Directly plugged the lan cable (internet) in the phone & Your Ip phone can communicate with your internal phones or internet phones . Specially Recommended for the internet connectivity . I also Implemented  ASA UC PROXY Setup For My Customer . Thanks & Regards Vishal Thakur 9871854195 ... View more

Sir, First of all Thanks For ur great reply.   Please see below.. And 2nd  thing i want high convergence during failover . If my voice call is running & ku band will be down then it should be translated to c band with minimum time means call should not be disconnected (real time application ..)..& same should be c band to ku band......Offset list will resolve this ..or not  or  i should use the ipsla for the same ... I want high convergence ....... please see my configuration  & what ll be the offset list & access list for the same .. pls tell me some idea.. My wan 1 is interface FastEthernet0/0 ip address 13.13.13.2 255.255.255.0 shutdown duplex auto speed auto & wan 2 is interface FastEthernet2/0 ip address 12.12.12.2 255.255.255.0 duplex auto speed auto and local lan is interface FastEthernet1/0 ip address 11.11.11.1 255.255.255.0 duplex auto speed auto And access list is access-list 101 permit ip 11.11.11.0 0.0.0.127 any   (for 1 to 126 ip) for data video  c band primary & ku band secodandry in case of failover access-list 102 permit ip 11.11.11.128 0.0.0.127 any  (for 129 to 254  & for  voice ku band  is primary & c band will be secondary in case of link failover . waiting for ur reply. Thanks Vishal 9310253052 ... View more

vishal kumar 2 posts since Jul 29, 2011 Sep 2, 2011 4:40 AM Currently Being Moderated vsat communication on cisco router through c& ku band modem with link failover it is vsat connectivity..........and we have 40 sites.................. &  every site having two modem one c band & another is ku band &  also one cisco router.......every  wan is coming through modems to  switch >>>>to router fe ports.............pls see the  diagram & details //////////  suggest me for better solution In this scenario we have two remote sites (remote  side 1 & remote side 2) which is connecting on IP GATEWAY . Working style of modem:- They are using c band modem & ku band modem (supports Rip V2).One end of both the modem is connected to switch & another end is communicating over satellite freq  with hub BASED IP GATEWAY. I Requirement for every site........... 1.If  packet is going through wan1 then return path should be wan 1.  If  forward path is wan 1 then return path should be wan1. Remote side 1 to  remote side 2 communication is given below. 2.Means  remote side 1 cband modem  >>>>>>huB BASED IP GATEWAY ) >>>>then it is going on remote side 2 c  band>>>& reverse     should be in the same band means C  band.... 3. i would like all the  video & data traffic translated to c band & in case of primary  link  down C band traffic  should be  translated on KU band. FOR VIDEO & DATA,  PRIMARY BAND IS C BAND & KU BAND IS SECONDARY . 4. In case of voice , i would like all the voice traffic translated to the  Ku band  & during primary  link down KU band traffic should be  translated on C band. For voice , KU Band is primary & C band is secondary. 5.C band  is working in star topology  (hub & spoke)& KU band  is working in mesh topology. In this figure, example is given for star. Diagram attached. Attachments: sites2.JPG (78.6 K) ... View more

Sir,      Thanks for Ur reply. 1. I think ,first of all ,we should used ripv2 on all the network . 2. pbr will be used for the voice ,video over wan 1 (primary)& wan2 secondary  &   for data wan2 will be primary (wan1 will be secondary) one route map on fe interface & set ip next hop wan1 or set ip next hop verify-ava wan1 ... We are using 1841 router on all the sites................having  2 ge port &one fe port............... Please find the configuration ..............  Given Below ...............& if there is any mistake please confirm me. Current configuration : 1213 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! memory-size iomem 5 ip subnet-zero ! ! ip cef no ip dhcp use vrf connected ! ! no ip ips deny-action ips-interface ! no ftp-server write-enable ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 13.13.13.2 255.255.255.0 shutdown duplex auto speed auto ! interface FastEthernet1/0 ip address 11.11.11.1 255.255.255.0 ip policy route-map data duplex auto speed auto ! interface FastEthernet2/0 ip address 12.12.12.2 255.255.255.0 duplex auto speed auto ! router rip version 2 network 11.0.0.0 network 12.0.0.0 network 13.0.0.0 ! ip http server no ip http secure-server ! ip classless ! ! access-list 101 permit ip 11.11.11.0 0.0.0.127 any   (for 1 to 126 ip) access-list 102 permit ip 11.11.11.128 0.0.0.127 any  (for 129 to 254 ) ! route-map data permit 10 match ip address 101 set ip next-hop 13.13.13.1 set ip next-hop verify-availability ! route-map data permit 20 match ip address 102 set ip next-hop 12.12.12.1 set ip next-hop verify-availability ! ! ! control-plane ! ! ! ! ! ! ! ... View more