Cisco Community
English
Register
The War in Ukraine - Supporting customers, partners and communities. LEARN MORE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Bobby Thekkekandam
‎05-15-2018

Cisco Employee
Recent Badges
Awards
Recent Badges
See all
50 Accepted Solution
15 Accepted Solution
1 Accepted Solution
5 Accepted Solution
50 Replies
20 Replies
10 Replies
5 Replies
100 Helpful Vote
30 Helpful Vote
Stats
Member since ‎12-04-2002
645
Posts
676
Helpful
83
Solutions
Certifications
ONEx Manager Green Belt
CX Baseline Training

Re: Layer3 Etherchannel over 2 microwave link - activity check?

Created by in Switching
03-02-2011
03-02-2011
Yes, even with the physical link up, PAgP will detect that the failure between the link partners and...

Re: VLAN Basics - need some clarification

Created by in Switching
03-02-2011
03-02-2011
At the low end, most switches are layer 2 only(2xxx), all the current 3xxx switches and higher have ...

Re: Problem with Catalyst 2924 XL! Ports 9-12 dead?

Created by in Switching
10-05-2010
10-05-2010
Hi Dimitrios,From the bootup sequence you included, it looks like ports 9-12 are failing the POST di...

Re: Password Recovery Issue (3750 switch)

Created by in Switching
10-04-2010
10-04-2010
Hi David,Yes, you must perform the password recovery procedure while connected to the stack master s...

Re: Hardware problems with a WS-C2950-24

Created by in Switching
09-28-2010
09-28-2010
Hi Stephen,In this case the error is occuring during the POST diagnostic on bootup, so unfortunately...

Re: VLAN4 goes down for 1 or 2 minute then it automatically goes

Created by in Switching
09-13-2010
09-13-2010
Hi Arup,When VLAN4 is down, are there any access ports that are members of VLAN 4 that are up/up OR ...

Re: crash catalyst 2350 when changing vtp transparent to vtp ver

Created by in Switching
09-08-2010
09-08-2010
Hi Jürgen,Based on the information you provided, I believe you are running into CSCtd46800 This is f...

Re: WS-X6724-SFP in 6509-E is PwrDown

Created by in Switching
08-26-2010
08-26-2010
This looks like a clear diag failure. Have you checked on the switch that the module powers on to se...

Re: How to remove configuration regarding an empty slot?

Created by in Switching
08-25-2010
08-25-2010
Hi,There's no elegant solution here unfortunately. Reloading the switch will clear it from the runni...

Re: ip tacacs source-interface can't be configured in 3750G

Created by in Switching
08-24-2010
08-24-2010
I believe you are running into CSCsm28901. The release note states that this problem occurs in 12.2(...

Re: ws-x4516 and ws-x4516/2 - identical or not?

Created by in Switching
08-23-2010
08-23-2010
To add to Reza's comments, the existence of the two Part IDs doesn't extend beyond the ordering tool...

Re: switchport block multicast is missing on Cat 6500

Created by in Switching
08-23-2010
08-23-2010
Hi,I tested this in the lab, and see it missing in 12.2(18)SXF12, and see the feature present in 12....

Re: PB ERR-DISABLE

Created by in Networking Documents
07-30-2010
07-30-2010
Hi Hatem,show interface Fa 1/0/5 status err-disabledwill give you the reason for why the port was er...

Re: Turning a 3560-24 port into a 48 port switch

Created by in Switching
07-28-2010
07-28-2010
Unfortunately, not with a 3560. With a 3750, you can use the stackwise functionality to turn two phy...

Re: VSS Redundancy Question VSL Link

Created by in Switching
04-23-2010
04-23-2010
If I understand you correctly, you have your edge devices dual homed to the VSS pair via a Multichas...
Public Statistics
Date Registered ‎12-04-2002 03:01 PM
Date Last Visited ‎05-15-2018 03:07 AM
Total Messages Posted 645
Total Helpful Votes Received 676
Helpful Votes Given To