About bmarchik1980

bmarchik1980 · 10-02-2019

I am configuring an 1852i WAP with the controller image. I'm following the steps located on: https://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/89/user_guide/b_ME_User_Guide_89/getg_started.htmlI have my management network (VLAN 10)...

bmarchik1980 · 03-04-2018

I am having issues getting my anyconnect clients to be able to hairpin. I had this functional on my 5505, and used the same configuration from the 5505 to establish the setup on the 5506. Clients are able to talk to resources on the LAN, but unable...

bmarchik1980 · 11-29-2017

I am setting up an ASA 5506-X and having trouble getting ASDM to launch. I have gone through several posts in the forum of others experiencing issues with ASDM launch but no matter what I try, I cannot seem to get it to work. Relevant portions of ...

bmarchik1980 · 04-18-2017

I added a 3rd WAP371 to my existing 2 WAP371 cluster last night and I am running into an issue I haven't seen before. When the device initially boots from default configuration, it grabs an IP via DHCP as expected and loads. Once loaded, I am able ...

bmarchik1980 · 12-11-2012

Hi everyone, I'm new to the forum. I have a Cisco ASA 5505 with a confusing (to me) NAT issue.Single external IP address (outside interface) with multiple static object NAT translations to allow port forwarding to various internal devices. The conf...

bmarchik1980 · 11-06-2019

After lots of messing around and multiple resets of the AP, I finally found the issue. The "old" switch that I linked into to for DNS resolution, DHCP, etc, had the client subnet VLAN configured under VLAN 1. So every time I configured the client s...

bmarchik1980 · 10-04-2019

You did wait for around 10 minutes after saving the configuration? The ap has quite a while to boot. Yes, I watch the boot sequence over console access and wait until it is at prompt to login before I move on. During boot I kept noticing that the AP...

bmarchik1980 · 10-04-2019

switchport trunk allowed vlan remove 10- No change in behavior, VLAN 10 was listed per Cisco's configuration guidelines. From:https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-3/b_Cisco_Mobility_Express_Deployment_Guide/b_Cisco_Mo...

bmarchik1980 · 03-14-2018

Sorry for the late reply, I have been out of town and didn't have a chance to try the suggested change. I tried the change this morning and it appears to have fixed the issue. I am able to access internal network resources and the internet via the ...

bmarchik1980 · 03-05-2018

In show run, the NAT statement appears higher than it actually processes in NAT: Manual NAT Policies (Section 1)1 (inside) to (outside) source static any any destination static VPN_Subnet VPN ...

Member Since	‎12-27-2004 02:42 PM
Date Last Visited	‎07-29-2020 12:06 AM
Posts	22

User Statistics

User Activity

1852I Inaccessible after ME initial setup

ASA 5506 Remote Access VPN Hairpin

ASA 5506-X ASDM Access

WAP371 failing after joining cluster

Remote Access VPN, no split tunneling, internet access. NAT translation problem

Re: 1852I Inaccessible after ME initial setup

Re: 1852I Inaccessible after ME initial setup

Re: 1852I Inaccessible after ME initial setup

Re: ASA 5506 Remote Access VPN Hairpin

Re: ASA 5506 Remote Access VPN Hairpin