buenas tardes el siguiente mensaje está apareciendo en un router 2911 el cual uso tambien como gateway de voz con trajetas FXO
Warning! DSPs1, in slot 0 are using non-default firmware from flash:
This is not recommended, the default version is 26.3.8
este es parte del SH VER
#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 18:32 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
AG_0288-R01 uptime is 32 minutes
System returned to ROM by power-on
System restarted at 15:25:32 VE Mon Jun 15 2015
System image file is "flash0:c2900-universalk9-mz.SPA.150-1.M4.bin"
Last reload type: Normal Reload
y el show voice dsp detailed
show voice dsp detailed
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ========== ===== ======= === == ========= == ===== ============
edsp 0001 01 g729r8 p 0.1 IDLE 50/0/1.1
edsp 0002 02 g729r8 p 0.1 IDLE 50/0/1.2
edsp 0003 01 g729r8 p 0.1 IDLE 50/0/2.1
edsp 0004 02 g729r8 p 0.1 IDLE 50/0/2.2
edsp 0005 01 g729r8 p 0.1 IDLE 50/0/3.1
edsp 0006 02 g729r8 p 0.1 IDLE 50/0/3.2
edsp 0007 01 g729r8 p 0.1 IDLE 50/0/4.1
edsp 0008 02 g729r8 p 0.1 IDLE 50/0/4.2
edsp 0009 01 g729r8 p 0.1 IDLE 50/0/5.1
edsp 0010 02 g729r8 p 0.1 IDLE 50/0/5.2
edsp 0011 01 g729r8 p 0.1 IDLE 50/0/6.1
edsp 0012 02 g729r8 p 0.1 IDLE 50/0/6.2
edsp 0013 01 g729r8 p 0.1 IDLE 50/0/7.1
edsp 0014 02 g729r8 p 0.1 IDLE 50/0/7.2
edsp 0015 01 g729r8 p 0.1 IDLE 50/0/8.1
edsp 0016 02 g729r8 p 0.1 IDLE 50/0/8.2
edsp 0017 01 g729r8 p 0.1 IDLE 50/0/9.1
edsp 0018 02 g729r8 p 0.1 IDLE 50/0/9.2
edsp 0019 01 g729r8 p 0.1 IDLE 50/0/10.1
edsp 0020 02 g729r8 p 0.1 IDLE 50/0/10.2
edsp 0021 01 g729r8 p 0.1 IDLE 50/0/11.1
edsp 0022 02 g729r8 p 0.1 IDLE 50/0/11.2
edsp 0023 01 g729r8 p 0.1 IDLE 50/0/12.1
edsp 0024 02 g729r8 p 0.1 IDLE 50/0/12.2
edsp 0025 01 g729r8 p 0.1 IDLE 50/0/13.1
edsp 0026 02 g729r8 p 0.1 IDLE 50/0/13.2
edsp 0027 01 g729r8 p 0.1 IDLE 50/0/14.1
edsp 0028 02 g729r8 p 0.1 IDLE 50/0/14.2
edsp 0029 01 g729r8 p 0.1 IDLE 50/0/15.1
edsp 0030 02 g729r8 p 0.1 IDLE 50/0/15.2
edsp 0031 01 g729r8 p 0.1 IDLE 50/0/16.1
edsp 0032 02 g729r8 p 0.1 IDLE 50/0/16.2
edsp 0033 01 g729r8 p 0.1 IDLE 50/0/17.1
edsp 0034 02 g729r8 p 0.1 IDLE 50/0/17.2
edsp 0035 01 g729r8 p 0.1 IDLE 50/0/18.1
edsp 0036 02 g729r8 p 0.1 IDLE 50/0/18.2
edsp 0037 01 g729r8 p 0.1 IDLE 50/0/19.1
edsp 0038 02 g729r8 p 0.1 IDLE 50/0/19.2
edsp 0039 01 g729r8 p 0.1 IDLE 50/0/20.1
edsp 0040 02 g729r8 p 0.1 IDLE 50/0/20.2
edsp 0041 01 g729r8 p 0.1 IDLE 50/0/21.1
edsp 0042 02 g729r8 p 0.1 IDLE 50/0/21.2
edsp 0043 01 g729r8 p 0.1 IDLE 50/0/22.1
edsp 0044 02 g729r8 p 0.1 IDLE 50/0/22.2
edsp 0045 01 g729r8 p 0.1 IDLE 50/0/23.1
edsp 0046 02 g729r8 p 0.1 IDLE 50/0/23.2
edsp 0047 01 g729r8 p 0.1 IDLE 50/0/24.1
edsp 0048 02 g729r8 p 0.1 IDLE 50/0/24.2
Warning! DSPs1, in slot 0 are using non-default firmware from flash:
This is not recommended, the default version is 26.3.8
----------------------------FLEX VOICE CARD 0 -----------------------
-------
*DSP VOICE CHANNELS*
CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending
LEGEND : (bad)bad (shut)shutdown (dpend)download pending
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
====== === == ========= ========== ===== ======= === == ========= == ==== ============
SP2600 001 01 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 02 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 03 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 04 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 05 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 06 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 07 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 08 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 09 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 10 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 11 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 12 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 13 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 14 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 15 None 0.0.0 bad idle 0 0 0 0/0
SP2600 001 16 None 0.0.0 bad idle 0 0 0 0/0
*DSP SIGNALING CHANNELS*
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
====== === == ========= ========== ===== ======= === == ========= == ==== ============
SP2600 001 01 {flex} 0.0.0 free idle 0 0 0/2/0 0 0/0
SP2600 001 02 {flex} 0.0.0 free idle 0 0 0/2/1 0 0/0
SP2600 001 03 {flex} 0.0.0 free idle 0 0 0/2/2 0 0/0
SP2600 001 04 {flex} 0.0.0 free idle 0 0 0/2/3 0 0/0
------------------------END OF FLEX VOICE CARD 0 ----------------------------
el router reconoce la tarjeta fxo,
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/2/0 -- fxo-ls up dorm idle on-hook y
0/2/1 -- fxo-ls up dorm idle on-hook y
0/2/2 -- fxo-ls up dorm idle on-hook y
0/2/3 -- fxo-ls up dorm idle on-hook y
NAME: "CISCO2911/K9 chassis", DESCR: "CISCO2911/K9 chassis"
PID: CISCO2911/K9 , VID: V02 , SN: FTX1452A0AY
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V01 , SN: FOC1125582A
NAME: "PVDM3 DSP DIMM with 16 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 16 Channels"
PID: PVDM3-16 , VID: V01 , SN: FOC14492AAX
NAME: "C2911 AC Power Supply", DESCR: "C2911 AC Power Supply"
PID: PWR-2911-AC , VID: V01 , SN: AZS144603A1
tengo bien configurados los dial peers pero las llamadas no ingresasn a los puertos y tampoco me deja realizar aPSTN.
alguna ayuda al respecto?
gracias
