04-16-2021 02:56 AM - edited 04-16-2021 04:41 AM
Hello,
I have a lab configured on dmvpn with eigrp, but on the hub i can't view any spoke and on the spoke there are the ip of the Hub but with a state : NHRP ( configuration below)
there are anyone here can help me please to make the state up.
HUB:
interface Tunnel1
ip address 172.16.0.8 255.255.255.0
no ip redirects
ip mtu 1476
ip nhrp authentication DMVPN
ip nhrp network-id 1
ip nhrp holdtime 100
ip nhrp nhs 172.16.0.8
ip nhrp redirect
ip tcp adjust-mss 1436
tunnel source 192.168.10.2
tunnel mode gre multipoint
Spoke:
interface Tunnel1
ip address 172.16.0.9 255.255.255.0
no ip redirects
ip mtu 1476
ip nhrp authentication DMVPN
ip nhrp map 172.16.0.8 192.168.10.2
ip nhrp map multicast 192.168.10.2
ip nhrp network-id 1
ip nhrp holdtime 100
ip nhrp nhs 172.16.0.8
ip nhrp shortcut
ip tcp adjust-mss 1436
tunnel source 192.168.11.2
tunnel mode gre multipoint
HUB
Router#sh dmvpn
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
T1 - Route Installed, T2 - Nexthop-override
C - CTS Capable
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding, W --> Waiting
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
SPOKE
Router#sh dmvpn
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
T1 - Route Installed, T2 - Nexthop-override
C - CTS Capable
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding, W --> Waiting
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface: Tunnel1, IPv4 NHRP Details
Type:Spoke, NHRP Peers:1,
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb
----- --------------- --------------- ----- -------- -----
1 192.168.10.2 172.16.0.8 NHRP 00:38:07 S
--------------------
EIGRP
HUB:
router eigrp DMVPN
!
address-family ipv4 unicast autonomous-system 1
!
topology base
exit-af-topology
network 123.0.0.0
network 123.8.8.8 0.0.0.0
network 172.16.0.0
exit-address-family
!
Spoke
router eigrp DMVPN
!
address-family ipv4 unicast autonomous-system 1
!
topology base
exit-af-topology
network 123.9.9.9 0.0.0.0
network 172.16.0.0
exit-address-family
!
Solved! Go to Solution.
04-18-2021 05:49 AM
any other suggestion here please !
04-16-2021 04:05 AM
Hello,
on the hub, it looks like you are missing the lines in bold:
interface Tunnel1
ip address 172.16.0.8 255.255.255.0
no ip redirects
ip mtu 1476
ip nhrp authentication DMVPN
--> ip nhrp map multicast dynamic
ip nhrp network-id 1
ip nhrp holdtime 100
ip nhrp nhs 172.16.0.8
--> no ip split-horizon eigrp 1
ip nhrp redirect
ip tcp adjust-mss 1436
tunnel source 192.168.10.2
tunnel mode gre multipoint
04-16-2021 04:22 AM
Thank you,
for the split-horizon, i used eigrp named ! how can i write eigrp 1 ?
and split-horizon didn't work with eigrp named
04-16-2021 05:03 AM
Hello,
router eigrp DMVPN
!
address-family ipv4 unicast autonomous-system 1
af-interface Tunnel1
no split-horizon
04-16-2021 05:27 AM
04-23-2021 03:19 AM
I have same problem, looking to this conversation like to some tv serial hoping to find any solutions.
Thanks all for your knowledge
04-28-2021 02:29 AM
hi again
any other solution here plz ! i try all the possible solution that i khonw but nothing is change !!
thank you for your helps
04-29-2021 06:00 AM
i found the solution
first check the mpls config and be sure that #sh mpls ldp nei is right
then check the ospf config and the redistribute of bgp and ospf in all the router
then check in the PE #sh ip bgp all sum or #sh ip bgp all is correct and the state is up.
this is what i did and now it's working.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide