10-23-2013 11:22 AM - edited 02-21-2020 07:16 PM
Hi,
I am setting up remote IPsec VPN using ASDM for ASA 5505.
can somebody guide me for FOLLOWING;
1. step 6 for ASDM IPsec wizard: pool name: which IP addresses I have to assign here.
my network has inside IP 192.168.0.1 and outside IP 162.212.232.174
2. for VPN client: what would be Host IP??
what would be group authentication user name and password??
Please advice or provide me any link that can help me for this set up??
I need help for both VPN client setup and ASDM wizard for IPsec wizard.
Thanks,
Sap
Solved! Go to Solution.
10-24-2013 07:06 AM
Hello,
Pool is the IP address range for VPN cleints (when connect to your network). Use a subnet different from your internal networks. ex: 192.168.10.0 255.255.255.0
Host IP: Your ASA 5505 public ip: 162.212.232.174
Group information- That you configure on ASA5505 and same needs to configured on client.
Check the below link (Search on line and you find lot of documentation).
http://www.databasemart.com/HowTo/Cisco_VPN_Remote_Access_Setup_ASA5500.aspx
Thx
MS
10-24-2013 06:53 PM
Hi,
This one is very useful
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080702992.shtml
Please let us know how it worked
Regards,
10-28-2013 11:00 AM
Hi,
Outside interface (VLAN2) down --> No.. it has to be up. Normally, the service provider Hand off connects to E0/0 of the ASA and E0/0 will be in Vla2. If it is showing down, You cannot access Internet from your LAN or you cannot access VPN host from outside. Thats why you are getting the error message.
Thx
MS
10-24-2013 07:06 AM
Hello,
Pool is the IP address range for VPN cleints (when connect to your network). Use a subnet different from your internal networks. ex: 192.168.10.0 255.255.255.0
Host IP: Your ASA 5505 public ip: 162.212.232.174
Group information- That you configure on ASA5505 and same needs to configured on client.
Check the below link (Search on line and you find lot of documentation).
http://www.databasemart.com/HowTo/Cisco_VPN_Remote_Access_Setup_ASA5500.aspx
Thx
MS
10-24-2013 06:53 PM
Hi,
This one is very useful
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080702992.shtml
Please let us know how it worked
Regards,
10-25-2013 10:01 AM
mvsheik123 wrote:
Hello,
Pool is the IP address range for VPN cleints (when connect to your network). Use a subnet different from your internal networks. ex: 192.168.10.0 255.255.255.0
Host IP: Your ASA 5505 public ip: 162.212.232.174
Group information- That you configure on ASA5505 and same needs to configured on client.
Check the below link (Search on line and you find lot of documentation).
http://www.databasemart.com/HowTo/Cisco_VPN_Remote_Access_Setup_ASA5500.aspx
Thx
MS
Thanks MS,
Host IP for VPN client will be outside interface IP for ASA???
I am trying that but getting attached error message.
pls advise
thx,
Sap
10-25-2013 09:17 AM
Thanks everyone for your comments,
now ASDM showing inside interface (VLAN1) up IP 192.168.1.1 and Outside interface (VLAN2) down.
Both should be up for remote VPN to work???
1. Please advise how I can make outside interface up and which IP address I have to assign using ASDM??
2. how I can assign inside IP in the same subnet as my network, because right now it is using defaut IP as inside IP.
Thanks,
Sap
10-28-2013 11:00 AM
Hi,
Outside interface (VLAN2) down --> No.. it has to be up. Normally, the service provider Hand off connects to E0/0 of the ASA and E0/0 will be in Vla2. If it is showing down, You cannot access Internet from your LAN or you cannot access VPN host from outside. Thats why you are getting the error message.
Thx
MS
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide