I am trying to set up the following remote access environment.
Cisco Router(ISR4331 AUX Port) ----- US Robotics 5686G modem(Router side) ======PSTN line====== US Robotics 5686G modem(PC side)----- PC
I give the command atdt<phone number> on PC side modem, the result is alwasy "NO CARRIER".
Could you please check my configuration of modem has problem?
◆US Robotics 5686G modem(PC side)
===============
ati4
U.S. Robotics 56K FAX EXT Settings...
B0 E1 F1 M1 Q0 V1 X4 Y0
BAUD=9600 PARITY=N WORDLEN=8
DIAL=TONE ON HOOK CID=0
&A1 &B1 &C1 &D0 &G0 &H0 &I0 &K0
&M4 &N0 &P1 &R1 &S0 &T0 &U0 &Y1
S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=004
S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S35=000 S36=014 S38=000 S39=010 S40=003
S41=000 S42=010
LAST DIALED #: T2144364959
OK
ati5
U.S. Robotics 56K FAX EXT NVRAM Settings...
Template Y0
DIAL=TONE B0 F1 M1 X4
BAUD=9600 PARITY=N WORDLEN=8
&A1 &B1 &G0 &H0 &I2 &K0 &M4 &N0
&P1 &R1 &S0 &T0 &U0 &Y1
S00=001 S02=043 S03=013 S04=010 S05=008 S06=004 S07=060
S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S15=000
S19=000 S21=010 S22=017 S23=019 S25=005 S27=000 S28=008
S29=020 S30=000 S31=128 S32=002 S33=000 S34=000 S35=000
S36=014 S38=000 S39=010 S40=003 S41=000 S42=010
Strike a key when ready . . .
Template Y1
DIAL=TONE B0 F1 M1 X4
BAUD=9600 PARITY=N WORDLEN=8
&A1 &B1 &G0 &H0 &I2 &K0 &M4 &N0
&P1 &R1 &S0 &T0 &U0 &Y1
S00=001 S02=043 S03=013 S04=010 S05=008 S06=004 S07=060
S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S15=000
S19=000 S21=010 S22=017 S23=019 S25=005 S27=000 S28=008
S29=020 S30=000 S31=128 S32=002 S33=000 S34=000 S35=000
S36=014 S38=000 S39=010 S40=003 S41=000 S42=010
STORED PHONE #0:
#1:
#2:
#3:
OK
ati7
Configuration Profile...
Product Type US/Canada External
Product ID: 00568606
Options V32bis,V.80,V.34+,V.90,V.92
Fax Options Class 1/Class 2.0
Line Options Caller ID, Distinctive Ring
Clock Freq 92.0Mhz
EPROM 256k
RAM 32k
FLASH date Dec 9 2009
FLASH rev V3.5.1
DSP date Dec 9 2009
DSP rev 15
Serial Num: 1MCWX71K2225
OK
◆US Robotics 5686G modem(Router side)
========================
ati4
U.S. Robotics 56K FAX EXT Settings...
B0 E1 F1 M1 Q0 V1 X1 Y0
BAUD=9600 PARITY=N WORDLEN=8
DIAL=TONE ON HOOK CID=0
&A1 &B1 &C1 &D0 &G0 &H0 &I0 &K0
&M4 &N6 &P1 &R1 &S0 &T0 &U6 &Y1
S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=004
S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S35=006 S36=014 S38=000 S39=010 S40=003
S41=000 S42=010
LAST DIALED #:
OK
ati5
U.S. Robotics 56K FAX EXT NVRAM Settings...
Template Y0
DIAL=TONE B0 F1 M1 X4
BAUD=9600 PARITY=N WORDLEN=8
&A3 &B1 &G0 &H1 &I0 &K1 &M4 &N0
&P1 &R2 &S0 &T0 &U0 &Y1
S00=001 S02=043 S03=013 S04=010 S05=008 S06=004 S07=060
S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S15=000
S19=000 S21=010 S22=017 S23=019 S25=005 S27=000 S28=008
S29=020 S30=000 S31=128 S32=002 S33=000 S34=000 S35=000
S36=014 S38=000 S39=010 S40=003 S41=000 S42=010
Strike a key when ready . . .
Template Y1
DIAL=TONE B0 F1 M1 X1
BAUD=9600 PARITY=N WORDLEN=8
&A1 &B1 &G0 &H0 &I0 &K0 &M4 &N6
&P1 &R1 &S0 &T0 &U6 &Y1
S00=002 S02=043 S03=013 S04=010 S05=008 S06=004 S07=060
S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S15=000
S19=000 S21=010 S22=017 S23=019 S25=005 S27=000 S28=008
S29=020 S30=000 S31=128 S32=002 S33=000 S34=000 S35=006
S36=014 S38=000 S39=010 S40=003 S41=000 S42=010
STORED PHONE #0:
#1:
#2:
#3:
OK
ati7
Configuration Profile...
Product Type US/Canada External
Product ID: 00568606
Options V32bis,V.80,V.34+,V.90,V.92
Fax Options Class 1/Class 2.0
Line Options Caller ID, Distinctive Ring
Clock Freq 92.0Mhz
EPROM 256k
RAM 32k
FLASH date Jun 29 2012
FLASH rev V5.4.5
DSP date Jun 29 2012
DSP rev 15
Serial Num: 1MCWZBRO0793
OK
========================
◆ Cisco Router ISR 4331(AUX Port)
========================
Router#show running-config | section line
line con 0
stopbits 1
line aux 0
password cisco
login
modem InOut
transport input all
flowcontrol hardware
line vty 0 4
login
transport input ssh
line vty 5 14
login
transport input ssh
Router#
========================
