cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
868
Views
0
Helpful
3
Replies

Required VPN troubleshooting.....

zakid
Beginner
Beginner

Dear Folks,

Cisco ASA5510,ver 8.2(2)16, ASDM 6.2, currently Site-to-Site, L2TPoverIPSEC RAVPN and Anyconnect VPN are configured and working successfully.

Recently Configured Cisco VPN Client IPSEC RAVPN, connecting Successfully, but resources cannot reachbility.

When I checked cisco VPN client statistics, I noticed Tunneling Protocol : Inactive

Some one can push me in right direction....

Configuration and test result attached.

Much Appreciated.

Thanks & regards,

3 Replies 3

Jitendra Siyag
Beginner
Beginner

that is not an issue. it simply shows that you are not using transport mode.

check the router tab and try to ping some destination from the subnets specified there.

and also the given config is not complete for the RAVPN. there will be tunel group and group policy also. are you using split-acl.

and you can try to check using packet tracer command if access is allowed for particular source and destination, when the client is connected.

Good Day,

Thanks mate,

Full configuration is pasted below for your view....

checked & verified packet tracer and other network tools , like ping and tracerroute, all seems to be fine.

Any thought..

Thanks & Much Appreciated.

crypto ipsec transform-set aes128sha esp-aes esp-sha-hmac
crypto ipsec transform-set aes128sha mode transport
crypto ipsec transform-set aes256sha esp-aes-256 esp-sha-hmac
crypto ipsec transform-set aes256sha mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map out_dyn_map 10 set transform-set aes128sha aes256sha ESP-3DES-SHA TRANS_ESP_3DES_MD5

crypto dynamic-map out_dyn_map 20 set pfs
crypto dynamic-map out_dyn_map 20 set transform-set ESP-3DES-SHA

crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
no crypto isakmp nat-traversal

tunnel-group MDT_TABLET_RAVPN type remote-access
tunnel-group MDT_TABLET_RAVPN general-attributes
address-pool MDT_TABLET_RAVPN
authentication-server-group MDT_RAVPN LOCAL
default-group-policy MDT_TABLET_RAVPN
tunnel-group MDT_TABLET_RAVPN ipsec-attributes
pre-shared-key *****

group-policy MDT_TABLET_RAVPN internal
group-policy MDT_TABLET_RAVPN attributes
dns-server value 10.1.x.x 10.1.x.x
vpn-tunnel-protocol IPSec
default-domain value mysecurevpn.com

Hardik Vaidh
Beginner
Beginner

Dear zakir

check my bold word. your phase 1&2 authentication dnt match.

check access list also for NAT and VPN

crypto ipsec transform-set aes128sha esp-aes esp-sha-hmac

crypto ipsec transform-set aes128sha mode transport

crypto ipsec transform-set aes256sha esp-aes-256 esp-sha-hmac

crypto ipsec transform-set aes256sha mode transport

crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac

crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-sha-hmac

crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport

crypto isakmp policy 10

authentication pre-share

encryption 3des

hash md5

group 2

lifetime 86400

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers