In this Document we will see how to add controllers to the Prime Infrastructure.
You can add controllers one at a time or in batches. To add controllers, follow these steps:
Step 1 Login Into Prime Infrastructure.
Choose Configure > Controllers.
Step 2 From the Select a command drop-down list, choose Add Controllers, and click Go. The Add Controller page appears.
Step 3 Choose one of the following:
If you want to add one controller or use commas to separate multiple controllers, leave the Add Format Type drop-down list at Device Info.
Using CSV Format
If you want to add multiple controllers by importing a CSV file, choose File from the Add Format Type drop-down list. The CSV file allows you to generate your own import file and add the devices you want.
When a controller is removed from the system, the associated access points are not removed automatically and therefore remain in the system. These disassociated access points must be removed manually.
If you are adding a controller into Prime Infrastructure across a GRE link using IPsec or a lower MTU link with multiple fragments, you might need to adjust the Maximum VarBinds per Get PDU and Maximum VarBinds per Set PDU. If it is set too high, the controller might fail to be added into Prime Infrastructure. To adjust the Maximum VarBinds per Get PDU or Maximum VarBinds per Set PDU, do the following: Stop Prime Infrastructure, choose Administration > Settings > SNMP Settings, and edit the Maximum VarBinds per Get PDU and Maximum VarBinds per Set PDU values to 50 or lower.
If you reduce the Maximum VarBinds per Get PDU or Maximum VarBinds per Set PDU value, applying the configurations to the device might fail.
Step 4 If you chose Device Info, enter the IP address of the controller you want to add. If you want to add multiple controllers, use a comma between the string of IP addresses.
If a partial byte boundary is used and the IP address appears to be broadcast (without regard to the partial byte boundary), there is a limitation on adding the controllers into Prime Infrastructure. For example, 10.0.2.255/23 cannot be added but 10.0.2.254/23 can.
If you chose File, click Browse to find the location of the CSV file you want to import.
The first row of the CSV file is used to describe the columns included. The first row of the CSV file is used to describe the columns included. The IP Address column is mandatory. The following example shows a sample CSV file.
Step 5 Select the Verify Telnet/SSH Credentials check box if you want this controller to verify Telnet/SSH credentials. You might want to leave this unselected (or disabled) because of the substantial time it takes for discovery of the devices.
Note Enter SNMP parameters for the write access, if available. If you enter read-only access parameters, the controller is added but Prime Infrastructure is unable to modify the configuration and Prime Infrastructure can not be registered as a trap receiver on that Controller. Step 6 Use the Version drop-down list to choose v1, v2, or v3.
Step 7 In the Retries text box, enter the number of times that attempts are made to discover the controller.
Step 8 Provide the client session timeout value in seconds. This determines the maximum amount of time allowed for a client before it is forced to reauthenticate.
Step 9 In the Community field, enter either public or private (for v1 and v2 only).
Note If you go back and later change the community mode, you must perform a refresh config for that controller.
Step 10 Choose None, HMAC-SHA, or HMAC-MD5 (for v3 only) for the authorization type.
Step 11 Enter the authorization password (for v3 only).
Step 12 Enter None, CBC-DES, or CFB-AES-128 (for v3 only) for the privacy type.
Step 13 Enter the privacy password (for v3 only).
Step 14 Enter the Telnet credentials information for the controller. If you chose the File option and added multiple controllers, the information applies to all specified controllers. If you added controllers from a CSV file, the username and password information is obtained from the CSV file.
Note The Telnet/SSH username must have sufficient privileges to execute commands in CLI templates. The default username and password is admin.
Step 15 Enter the retries and timeout values. The default retries number is 3, and the default retry timeout is 1 minute.
When a controller is added to Prime Infrastructure, Prime Infrastructure acts as a TRAP receiver and the following traps are enabled on the controller: 802.11 Disassociation, 802.11 Deauthentication, and 802.11 Authenticated.
To update the credentials of multiple controllers in a bulk, choose Bulk Update Controllers from the Select a command drop-down list.
The Bulk Update Controllers page appears. You can choose a CSV file. The CSV file contains a list of controllers to be updated, one controller per line. Each line is a comma separated list of controller attributes.
The first line describes the attributes included. The IP address attribute is mandatory. For details, see the Cisco Prime Prime Infrastructure Configuration Guide.
Note After adding a controller, it is placed temporarily in the Monitor > Unknown Devices page while Prime Infrastructure attempts to communicate with the controller that you have added.
Once communication with the controller has been successful, the controller moves from the Monitor > Unknown Devices page to the Monitor > Controllers page.
If Prime Infrastructure is unable to successfully communicate with a controller, it remains in the Monitor > Unknown Devices and an error condition an error message is displayed. To access the Unknown Devices page, choose Configure > Unknown Devices.
Just wondering what the best practice is on using DHCP proxy mode vs DHCP bridging mode for roaming clients (L2 / L3 roam)? Does the DHCP proxy feature add significant time to the DHCP handshake and cause roaming clients to lose packets when they go ...
Hi all, I am having issues setting up a few Aironet 1262s (AIR-LAP1262N-E-K9) They are powered from a 3560 PoE-8 (only one at a time) and they power up...The power comes on and the light flashes green for bit (I assume booting)The light then is ...
Hi all, I am using WLC 3504 and i have created a open ssid that require web auth. I have also enabled a lobby admin account on my WLC to create accounts for guests to connect to this ssid. The default ip of the interface of this ssid is 188.8.131.52. For ...
Hello everyone,I am a new customer of Cisco Access Point AIR-AP2802E-E-K9C. I don't have much experience with this class of hardware Cisco. Could someone help me, how to configure this AP? I have experience with switches and routers. I would like, to this...
Dear all, I cannot reimage AP1852i through rommon mode .I tried below commands but it doesn't work. When it boot, it will load the old image (the old image has an issue so I cannot access to controller cli or webui)tftpboot AIR-AP1850-K9-8-5-151...