Hi Everybody
I have a WLC v7.4.100.0 and a AIR-CAP2602I-E-K9 and they are working perfectly. I got a new AIR-CAP2702I-E-K9 it gets an IP address but it does not talk to the WLC.
Can somebody help please.
Thank you.
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JC, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Fri 11-Dec-15 11:55 by prod_rel_team
Antigua Board Pre-Pilot
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 240 files, 8 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 20210688
flashfs[2]: Bytes available: 20689920
flashfs[2]: flashfs fsck took 11 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-CAP2702I-E-K9 (PowerPC) processor (revision A0) with 376814K/134656K bytes of memory.
Processor board ID FCW2022NMXZ
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.2.100.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: ..............................
Part Number : ............................
PCB Serial Number : .....................
Top Assembly Part Number : .................
Top Assembly Serial Number : ..........................
Top Revision Number : A0
Product/Model Number : AIR-CAP2702I-E-K9
% Please define a domain-name first.
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:13.479: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:13.527: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:13.527: Starting Ethernet promiscuous mode
*Mar 1 00:00:13.535: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg config failed, trying backup...
*Mar 1 00:00:13.535: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg.bak config failed...
*Mar 1 00:00:14.835: %LWAPP-4-CLIENTEVENTLOG: PnP waiting for capwap init
*Mar 1 00:00:15.511: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:15.575: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JC, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Fri 11-Dec-15 11:55 by prod_rel_team
*Mar 1 00:00:15.575: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:00:15.611: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:15.619: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
*Mar 1 00:00:15.627: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg config failed, trying backup...
*Mar 1 00:00:15.627: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg.bak config failed...
*Mar 1 00:00:15.627: spamInitRadCfg: recovery image default mode 0
lwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:15.795: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:16.607: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:17.615: %LINK-5-CHANGED: Interface GigabitEthernet1, changed state to administratively down
*Mar 1 00:00:20.415: DPAA Initialization Complete
*Mar 1 00:00:20.415: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:21.415: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:23.415: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:24.415: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:27.611: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:28.611: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:29.707: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.20.11.66, mask 255.255.255.0, hostname APcc16.7ea5.fcd8
bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:34.535: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg config failed, trying backup...
*Mar 1 00:00:34.535: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg.bak config failed...
*Mar 1 00:00:34.535: %CAPWAP-3-EVENTLOG: No Config Present. PNP required
*Mar 1 00:00:34.539: Cert ISSUER (39): cn=Cisco Manufacturing CA SHA2,o=Cisco
%Error opening flash:/capwap-saved-config (No such file or directory)
%Error opening flash:/capwap-saved-config-bak (No such file or directory)
Not in Bound state.
*Mar 1 00:00:53.139: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.20.11.66, mask 255.255.255.0, hostname APcc16.7ea5.fcd8
Not in Bound state.
*Mar 1 00:01:08.095: %LWAPP-4-CLIENTEVENTLOG: Invoking capwap discovery
*Mar 1 00:01:11.167: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.20.11.66, mask 255.255.255.0, hostname APcc16.7ea5.fcd8
Loading http://devicehelper.cisco.com/ca/trustpool !
Loading http://devicehelper.cisco.com/ca/trustpool !
Not in Bound state.
*Mar 1 00:03:45.595: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.20.11.66, mask 255.255.255.0, hostname APcc16.7ea5.fcd8
