cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1613
Views
0
Helpful
7
Replies

client ap Urgent

jcastanos
Level 1
Level 1

I have a UWN architecture with two controllers 2106 and 1242AG access point.

My problem is that when I connect a client ( who is an AP Moxa) is not working properly because users that are connected behind that AP can not connect to the network

What I can do? Do I Convert it to HREAP LAP device? do i Convert all LAP to autonomous and discard WLC?

7 Replies 7

Rasika Nayanajith
VIP Alumni
VIP Alumni

What is the software version running on your 2106 ? Also if possible attach "show wlan <wlan_ID>" output for the WLAN you having issues

 

HTH

Rasika

**** Pls rate all useful responses ****

Versión 6. WLC..

 

I think  problem it's bridging...  client AP is a Moxa 1121 , this access point  only support CLIENT AP.

 

 

 

 

Few suggestions

1. Upgrade your WLC to 7.0.250.0 code. Here is the release notes for that version

http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn70mr5.html

2. Instead of using WEP as L2 security, use WPA2/PSK with AES

3. Disable "Client loadbalance" feature on your SSID

 

If I understand correctly, if you connect a wired client to Moxa 1121, that client cannot communicate to your network via 1242/2106 set up. Is that the issue ?

Pls do not forget to rate our responses if that is useful to you.

HTH

Rasika

 

yes,

 

 It's not posible upgrade  software WLC . Moxa client  i think not support WPA

Hi

As per this Moxa 1121 support WAP2, check with your Moxa support people as well.

http://www.moxa.com/product/AWK-1121_Series.htm

You have to bring WLC to a supported code even if you want to get TAC support. I am sure in 7.0.x you can connect wired client behind a work group bridge to WLC managed AP.

In this example cisco AP used as WGB to connect a wired client to CUWN network running on 7.0.116.0 code.

http://mrncciew.com/2013/04/30/wgb-with-capwap/

 

HTH

Rasika

**** Pls rate all useful responses ****

WLAN Identifier.................................. 1

Profile Name..................................... Logis

Network Name (SSID).............................. LOGIS

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

AAA Policy Override.............................. Disabled

Network Admission Control

 

  NAC-State...................................... Disabled

  Quarantine VLAN................................ 0

Number of Active Clients......................... 3

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ management

WLAN ACL......................................... unconfigured

DHCP Server...................................... Default

DHCP Address Assignment Required................. Disabled

 

--More-- or (q)uit

Quality of Service............................... Silver (best effort)

Scan Defer Priority.............................. 5,6

Scan Defer Time.................................. 100 milliseconds

WMM.............................................. Allowed

Media Stream Multicast-direct.................... Disabled

CCX - AironetIe Support.......................... Enabled

CCX - Gratuitous ProbeResponse (GPR)............. Disabled

CCX - Diagnostics Channel Capability............. Disabled

Dot11-Phone Mode (7920).......................... Disabled

Wired Protocol................................... None

IPv6 Support..................................... Disabled

Peer-to-Peer Blocking Action..................... Disabled

Radio Policy..................................... All

DTIM period for 802.11a radio.................... 1

DTIM period for 802.11b radio.................... 1

Radius Servers

   Authentication................................ Global Servers

   Accounting.................................... Global Servers

   Dynamic Interface............................. Disabled

Local EAP Authentication......................... Disabled

Security

 

   802.11 Authentication:........................ Open System

Static WEP Keys............................... Enabled

        Key Index:...................................... 1

        Encryption:..................................... 104-bit WEP

   802.1X........................................ Disabled

   Wi-Fi Protected Access (WPA/WPA2)............. Disabled

   CKIP ......................................... Disabled

   Web Based Authentication...................... Disabled

   Web-Passthrough............................... Disabled

   Conditional Web Redirect...................... Disabled

   Splash-Page Web Redirect...................... Disabled

   Auto Anchor................................... Disabled

   H-REAP Local Switching........................ Disabled

   H-REAP Learn IP Address....................... Enabled

   Infrastructure MFP protection................. Enabled (Global Infrastructure MFP Disabled)

   Client MFP.................................... Optional but inactive (WPA2 not configured)

   Tkip MIC Countermeasure Hold-down Timer....... 60

Call Snooping.................................... Disabled

Band Select...................................... Enabled

Load Balancing................................... Enabled

 

 i feel honored ... you are  a wireless GURU.

Review Cisco Networking for a $25 gift card