Embedded Packet Capture config on IE3400

[gunheon103]

monitor capture test access-list test1
monitor capture test limit duration 1000
monitor capture test interface gigabitEthernet 1/3 both
monitor capture test buffer circular size 100
monitor capture test start

monitor capture test access-list test
monitor capture test limit duration 1000
monitor capture test interface gigabitEthernet 1/3 both
monitor capture test buffer circular size 100
monitor capture test start

위의 명령어가 작동이 안됩니다.

interface GigabitEthernet1/1
!
interface GigabitEthernet1/2
!
interface GigabitEthernet1/3
switchport access vlan 10
switchport mode access
!
interface GigabitEthernet1/4
!
interface GigabitEthernet1/5
!
interface GigabitEthernet1/6
!
interface GigabitEthernet1/7
!
interface GigabitEthernet1/8
!
interface GigabitEthernet1/9
!
interface GigabitEthernet1/10
!
interface AppGigabitEthernet1/1
!
interface Vlan1
no ip address
shutdown
!
interface Vlan10
ip address 172.16.10.1 255.255.255.0
!

ip access-list standard test1
10 permit any
!
ip access-list extended test
10 permit ip any any

위와 같이 설정 했는데 아래와 같이 문구가 뜨면서 작동이 안됩니다.

예시 config 를 받을수  있을까요 ?

IE3400_1#monitor capture test start

IE3400_1#monitor capture test start
Configuration failed. Can not have ACL based classification in a class-map epc_class_test within an output policy-map

Configuration failed. Can not have ACL based classification in a class-map epc_class_test within an output policy-map

Unable to activate Capture.

IE3400_1#
*Oct 7 06:21:53.031: %QOS-6-POLICY_INST_FAILED: Service policy installation failed on GigabitEthernet1/3. . policy:epc_policy_test, dir:OUT, ptype:PACKET_SERVICE, ctype:EPC

참고문서

https://www.cisco.com/c/en/us/td/docs/switches/lan/cisco_ie3X00/software/17_3/b_network_mgmt_17-3_iot_switch_cg/m_epc.html

[MHM Cisco World]

can I see the ACL (test)

Thanks A Lot
MHM

[gunheon103]

ip access-list standard test1
10 permit any
!
ip access-list extended test
10 permit ip any any

Are you talking about this? I don't have anything else.

Thank you.

[MHM Cisco World]

I want to check it, 
if it permit any then why you add it, 
remove the ACL from capture and check again. 

Thanks A Lot
MHM

[gunheon103]

You must add acl to enable embedded packet capture.

IE3400_1#monitor capture test start
Filter not attached to capture

Unable to activate Capture.

[balaji.bandi]

what is the version of the code running,

try below example with out any extended ACL :

https://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-embedded-packet-capture/116045-productconfig-epc-00.html

[gunheon103]

https://www.cisco.com/c/en/us/td/docs/switches/lan/cisco_ie3X00/software/17_3/b_network_mgmt_17-3_iot_switch_cg/m_epc.html

ROM: IOS-XE ROMMON
BOOTLDR: Version 7.1.14 [RELEASE SOFTWARE] crashkernel=64M
IE3400_1 uptime is 16 hours, 41 minutes
Uptime for this control processor is 16 hours, 42 minutes
System returned to ROM by power-on
System image file is "flash:ie3x00-universalk9.17.06.03.SPA.bin"
Last reload reason: power-on

IE-3400-8T2S

IE3400_1#monitor capture test start
Filter not attached to capture

Unable to activate Capture.