05-13-2022 03:53 AM
Hi,
I've researched this issue and so far haven't found a similar case, so I've signed up to ask for some advice
I have an MR36 running 27.7.1 connected to an MS250-48LP running in test as a PoC for a network wide roll out
I have a Guest SSID distibuting it's own DHCP, and a Production SSID configured to use the local LAN DHCP server.
In the production SSID, I'm getting the DHCP error in the subject, however, clients are getting a valid IP address from the server, with the correct gateway etc, and a lease visible in the DHCP lease list on the Windows server. However the client claims there is no internet access
The MS250 is currently configured to block rogue DHCP servers but specifically allow the DHCP server in question, it's worth noting that client devices connected to the switch via copper are getting addresses and connecting out without issue, there is no L3 configured on this network
Any suggestions of where to look would be a great help, thanks in advance
Solved! Go to Solution.
01-22-2024 06:57 AM
Well we resolved the issue. We have an ASA in our environment with basic threat detection enabled. When doing a packet tracer on the ASA the client experiencing the issue was Shunned in Phase 3. When looking at the policy we have excluded subnets from the threat detection with auto recovery after 3600 seconds (1 hour). Once we added that in the policy we have not had the issue occur again.
05-13-2022 12:50 PM
If you run a packet capture on the wired interface of the AP on which the client is connected, do you see the full DORA exchange as a client tries to associate with the network?
It's been a while since my windows days, I assume it should only populate the lease table after the Ack back from the endpoint?
On the client itself, do you see the entire IP assignment configured as expected, IP, mask, gateway, VLAN?
Does the communication only not work if going towards the internet?
Are you able to ping the gateway?
Could you have some L3 block, possibly a missing return route upstream of the MS?
Are the wired clients on the same VLAN as the wireless clients?
06-22-2022 02:39 PM
Ughhhhh.. meant after the ACK is sent by the server, not the client.
05-16-2022 12:08 PM
I would start up upgrading to the stable firmware version. You might be fighting issues that no longer exist.
You are a major version out of date.
05-16-2022 01:00 PM
Is your client device set to pick DNS using DHCP as well or is it manually assigned? If you try manually setting DNS severs does the error go away?
05-18-2022 03:50 AM
Thanks for the suggestions guys, I'm out of office this week until Friday, so will pick up with your ideas and report back then
05-18-2022 08:45 AM
Have you checked the L3 rule under Wireless ->> Firewall and Traffic shaping? I have seen that rule block traffic going to the servers on the LAN. Change that deny to allow and see if that fixes it.
05-23-2022 07:21 AM
Hi Guys, I've managed to put some time aside for this, and to answer some of the questions above, there is no Layer 3 happening on this network currently everything is on default VLAN 1, the Local LAN rule is set to allow, the client gets a valid address but can't ping the gateway, let alone the internet, and there are numerous other AP's with the same config on the same firmware functioning in other businesses under the same corporate ownership. The following packet capture shows the DHCP exchange from the server at x.x.x.2:
--- Start Of Stream ---
reading from file /tmp/click_pcap_dump, link-type EN10MB (Ethernet), snapshot length 9600
14:06:47.108066 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 307
14:06:48.607392 ARP, Request who-has x.x.x.87 tell x.x.x.2, length 46
14:06:50.094866 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 313
14:06:50.121799 ARP, Request who-has x.x.x.2 tell x.x.x.222, length 46
14:06:50.122399 ARP, Reply x.x.x.2 is-at xx:xx:xx:xx:xx:xx, length 46
14:06:50.923239 ARP, Request who-has x.x.x.196 tell x.x.x.2, length 46
14:06:58.177514 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 307
14:06:58.180722 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 307
14:06:58.181458 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 307
14:07:01.092245 ARP, Request who-has x.x.x.218 tell x.x.x.2, length 46
14:07:02.023750 ARP, Request who-has x.x.x.205 tell x.x.x.2, length 46
14:07:02.625115 ARP, Request who-has x.x.x.2 tell x.x.x.187, length 46
14:07:02.641458 ARP, Request who-has x.x.x.208 tell x.x.x.2, length 46
14:07:02.643704 ARP, Request who-has x.x.x.187 tell x.x.x.2, length 46
14:07:02.908839 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 307
14:07:06.860131 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 313
14:07:06.886681 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 307
14:07:08.944501 IP x.x.x.2.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 307
14:07:09.637136 ARP, Request who-has x.x.x.98 tell x.x.x.2, length 46
14:07:12.352409 ARP, Request who-has x.x.x.125 tell x.x.x.2, length 46
14:07:12.364550 ARP, Request who-has x.x.x.128 tell x.x.x.2, length 46
14:07:15.237527 ARP, Request who-has x.x.x.2 (xx:xx:xx:xx:xx:xx) tell x.x.x.222, length 46
14:07:15.238167 ARP, Reply x.x.x.2 is-at xx:xx:xx:xx:xx:xx, length 46
--- End Of Stream ---
Any thoughts!? Thanks in advance....
06-13-2022 05:28 AM
Hi Martyn,
Did you manage to fix this? We have a similar issue...
Thanks
Mark
06-13-2022 05:55 AM
Sadly not, no! Still hoping someone discovers this and knows the solution! Comforting to know I'm not alone however!
06-15-2022 01:18 AM
I have a similair issue where a MS-410 acting as a DHCP server does not fullfill a DHCP request, running Wireshark on both client and switch I can see the DHCP Discover but never the Offer coming thru from the switch
I have been spoken to Meraki support and they recommend by rebooting the switch and see if this resolves the issue. Not ideal as I would much prefer to get a root cause of this issue.
06-15-2022 01:21 AM
I'm not convinced that this is a DHCP server issue, as we are seeing this on Corporate and Guest SSIDs both of which use different DHCP servers - Corporate a Windows server and Guest DHCP is running on a Firewall.
06-15-2022 02:07 AM
In for a penny...... I just rebooted my switch, as it isn't technically in a production environment yet, so almost no impact on anyone beyond myself...... Rebooting the switch obviously caused a reboot of the AP and I'm still seeing the same issue on the SSID distributing DHCP from the Domain Server, the Laptop does have a valid address, I've released it, reserved it and then renewed to force the server to issue a new address, but nada, can't ping the gateway or anything else. The other SSID works fine using the AP's own DHCP service, devices can browse out through that without issue
06-15-2022 04:53 AM
Anyone using this...?
Cisco Meraki Wireless Health API Integration - Splash Access Cisco Meraki
06-15-2022 05:20 AM
I have access to a "Health" page, under Wireless>Monitor that offers a lot of information regarding indivdual client experience, is this something different?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide