Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi my putty is blank when i connect to my aironet using serial cable. Speed already change to 9600, help me
Hello Cisco WLAN experts,I noticed that our 9800-WLC is showing wrong BSSID-MAC instead of Base Radio MAC in the Neighboring APs list:Why is the WLC-9800 not able to show AP-names instead of BSSID-MAC-adresses ?Does it make sense to show the second 5...
Hi,We have a AIR-AP2802I-E-K9 access point that we're managing remotely, the access point is off-site. We need to reboot the access point via the controller. I can see an option under the General tab when I click into the access point which states 'H...
お世話になっております。この度、無線APをC9166Iに置き換えしたのですが、全ての無線APがチャネル36で起動してしまいます（チャネル設定は自動）また、動的チャネル割り当てアルゴリズムの間隔は24Hで設定しておりますが、24H経過してもチャネル36から変わらず、チャネル干渉により通信が不安定となる事象が発生しております。（24H間隔で自動的にチャネル干渉が起こらないように調整される認識です） これはWLCの設定の問題なのか、それ以外の問題なのかご存知の方いらっしゃいますか。よろしくお願いいたし...
Hello everibody. On a Cisco 5520, can the management interface and a dynamic (WLAN) interface have IP address on the same subnet? Lets say 192.168.20.X/24 An end-user tried to do this IP assigment and apparently received an error stating that the IP...
Hello Team, Please help the steps to upgrade the image to cisco access point manually through tftp in cli.The access point keeps reloading and not able type any commands.Tried resetting through the mode button but no luck. Here the actual issue, the ...
We have multiple spare units of IW-6300H-AC-H-K9 rebooting continuously and not joining Cisco 9800-l-c-k9 WLC (IOS 17.3.x) at the location, upon reviewing console these were the error messages[*08/18/2022 10:15:44.1638] systemd[1]: wcpd.service faile...
Hi ,If the Cisco 9800 WLC is connected to the core network via a Layer 3 link, how is this setup feasible? Cisco recommends avoiding the use of SVIs on the WLC side. Instead, it is best practice to configure the SVI on the core switch and use the ip ...
Hello,We currently have an SSID that is used for Video calls using iPad devices high density environment. I noticed today after a health check, that our Video SSID is using the Radio Policy "802.11a Only". I'm convinced this is the reason for our qua...
Resolved! APs not able connecting to controller
Hi!We are a small science institut having like 35-40 Cisco access points that are connected to the near-by University and their Cisco Wireless Controller (9800-40-A?). However, some of those APs do loose their connection to the WLC or cannot find the...
Currently have 3 large site which are all high density APs.1 site is controlled by a 9800 which was recently running co existence with a 8500 up to couple of weeks ago.Other 2 sites are supported by 5520s, with 2800APs, running the latest code.(Don’t...
Hi everyone,I'm currently working on a practical WiFi lab. The goal is to broadcast SSIDs mapped to two different VLANs: VLAN 20 and VLAN 30. I'm using the Cisco 9800-CL Wireless LAN Controller (WLC) deployed as a VM on VMware Workstation running on ...
I have 2 WLC and 30 AP. 25 AP set manually to register to WLC-1 by setting the primary controller pointed to the WLC-1 and 5 AP to WLC-1. The AP is working normally but when WLC-1 down why all 25 AP joined to the WLC-2? WLC-1 and WLC-2 located in sa...
Hello all, i have a question regarding aWIPS on Catalyst Centre. Currently in the project that i'm working on, we already successfully enable the rogue and aWIPS. The catalyst centre able to capture the threats. However, i just want to ask regarding ...
Hi all, I am new in this forum , and I am having same issue. I have installed ME on a second hand AP2802i, exactly: AIR-AP2800-K9-ME-8-10-196-0.tar, after installation finish I have configured it. I am able to ping the management interface IP from my...
