cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
98289
Views
11
Helpful
36
Replies

Client made a request to the DHCP server, but it did not respond

MartynB1
Community Member

Hi,

I've researched this issue and so far haven't found a similar case, so I've signed up to ask for some advice

I have an MR36 running 27.7.1 connected to an MS250-48LP running in test as a PoC for a network wide roll out

I have a Guest SSID distibuting it's own DHCP, and a Production SSID configured to use the local LAN DHCP server.

In the production SSID, I'm getting the DHCP error in the subject, however, clients are getting a valid IP address from the server, with the correct gateway etc, and a lease visible in the DHCP lease list on the Windows server. However the client claims there is no internet access

The MS250 is currently configured to block rogue DHCP servers but specifically allow the DHCP server in question, it's worth noting that client devices connected to the switch via copper are getting addresses and connecting out without issue, there is no L3 configured on this network

Any suggestions of where to look would be a great help, thanks in advance

36 Replies 36

MarkB
Community Member

Yes splash portal is an add-on.

Thanks

Mark

Phil Nape
Frequent Visitor
Frequent Visitor

Hi,

If the wireless config was the issue then you would see it on dashbaord when looking at the client page. Assuming that your setup is correct, and considering that the SSID works elsewhere in the business, I would look at the DHCP/ Radius Servers, do we have the users from the affected site in the correct groups and also where they authenticate, what happens after they authenticate ?, ipconfig /all from affected user and can we ping the DNS from affected user and or switch

Also test by setting up the SSID not to use any authentication and have a user connect and test ( Access Control>Network Access>open no encryption )

But before everything, please make sure you firmware is up to date on both MR's and MS's

Hope this read will not be a waste of time lol

Regards

Phil

Shamwedge
Community Member

I'm getting this same error for multiple clients.

This appears to only be happening on SSID's where client IP assignment is configured to Local LAN. I'm wondering if this is simply a software bug caused by having bridge mode enabled.

Outside of the error message, cleints do connect without issues.

We have just changed from L3 roaming to L2 Bridge mode and we are seeing this in both modes. We did have 2 DHCP servers configured, we have recently removed the second one and the errors have reduced but not gone away completely.

MartynB1
Community Member

Hi Guys, I've been away from the office a lot recently, however I set the AP's to update to the latest firmware on Monday and have just got back in to the office for testing today.....

Switches and AP's all now running the latest firmware, when I said the same setup was running in the other businesses we support, I was referring to the firmware version at the time, and the SSID configuration, the SSID I'm having an issue with isn't functioning elsewhere in the organisation, it is however identically configured to others that are functioning as they should

There is no Layer 3 config on this network, nor is there any Radius, the SSID is set up to use a PSK in Bridge Mode with a single Windows 2008R2 DC serving DHCP. I have tried your suggestion and mirrored this setup in a test SSID with open access (no PSK) and have the same issue;

Client made a request to the DHCP server, but it did not respond.request_ip='x.x.x.219' request_server='x.x.x.2' details='no_dhcp_response' radio='1' vap='2' channel='108' rssi='50'

However, the client has a valid IP address, DNS server entries and gateway ip as well as the correct DNS Suffix, yet can't ping any of the above

How do I go about raising a ticket with support?

robhuijser
Community Member

Hi Guys, I do not see any solution in this thread, also Meraki support is not knowing this issue.

packet trace must give some answers to all our questions but it happens not often and not always.

We are running an enterprise solution with 2 forwarded DHCP servers in our datacenter using radius authentication, no firewall rules and only seeing the issue on one specific SSID. Never had the issue before for the last 3 years. Both DHCP/DNS servers are up and running and are the most important servers in our environment, so 100% up

Is there an article with the solution?

image.png

WaseemD1
Community Member

Hi guys,
We have been suffering with this issue for more than ten months; we have three separate environments in various locations, each running the Meraki solution, all connected to the same radius server via LAN, and each using a different brand of DHCP server and routers.
This problem only affects one place for prolonged time, and it happened only once on another location but only for 1 day.
This issue affects users in a complete random manner, no specific details nor device type/NIC make was detected.
we have 1500+ user in the environment with more than 15 different devices, NIC and drivers.


Following a thorough study and checks, we have discovered the following:

  • According to pcaps from clients and (AP's wireless); discover requests are sent, however they are never shown on the switch nor (AP Wired) captures..
    Before the discover packets can reach the (AP Wired) pcaps, they are lost.
  • The DHCP server's packet captures indicate that the client has not sent any packets, but any successful connection does indicate a full DHCP DORA.
  • 4 or more clients may successfully connect to and finish the DORA on the same AP where a client fails to do so.
  • We attempted to restart all of the devices in production,, also we upgraded the Meraki APs and switches to the most recent firmware release but without success.

The workaround we have thus far involved is moving the problematic machine to another AP (Roam), trying to connect again and it succeed, then returning to the same location while still being connected, even when reconnecting will be successful.

The device connects and complete the DORA when roamed.


Please let us know if this was useful and if anyone had a solution for this problem.

Support from Meraki was of no assistance at all.

A big thank you!


Regards,
Waseem

-

AshP
Community Member

Hey folks,

This might help only small % of cases but the same error:

Client made a request to the DHCP server, but it did not respond.

type='NO DHCP response' associated='true' radio='0' vap='0'

The MX was removed, there was a modem swap and techs suspected new modem (GW Mode) being an issue. Rebooting did not resolve the issue, firmware wasn't upgraded but upon checking this was naturally related to VLAN Tagging. Everything works fine on simply disabling that, in these type of change scenarios.

_________

Check from:

Configuration overview

SSIDs

VLAN tag

This column refers to VLANs set in Bridge or L3 roaming. For info about VLANs used for VPN, see the VPN column below.

Then Go to:

Access control

Scroll down to: Client IP and VLAN

Disable VLAN tagging

(VLAN tagging is used to direct traffic to specific VLANs. To use VLAN tagging, all Meraki APs functioning as gateways in this network must be connected to switches that support IEEE 802.1Q.

The gateways must be connected to switch ports that are configured to accept 802.1Q tagged Ethernet frames (such ports are sometimes called "trunk ports").

If you are unsure, don't enable this feature.)

Hope this helps someone at least. 🙂

rahulkushawah
Community Member

@MartynB1 , Are you still facing this issue or its resolved? I am facing the same issue but its reported by Mac Devices only.

Unexpectedly failed DHCP because the DHCP server rejected the client’s request, but the client had a successful connection to SSID for a few seconds on AP

CyberSnort
Community Member

Client made a request to the DHCP server, but the DHCP server rejected the client's request.server_ip='1X.1X.1X.X9' request_server='unknown' details='dhcp_nack' radio='1' vap='0' channel='36' rssi='8'

Same issue. Any Suggestion ?

Have you tried removing VLAN tagging from the SSID in situations where AP wired interface is in the same VLAN as the one you want to tag? So for me I was using VLAN 700 as the LAN and 34 for guest, the AP pulled an IP for itself from 700 as I'd configured on the switch side (trunk native VLAN 700, tagged 34 and 700), but it didn't like having the VLAN tagging set for VLAN 700 in the SSID as well. Removing this fixed the issue right away.

sysint-12
Level 3
Level 3

Good Afternoon. Firstly I'm not trying to be patronising or insult your intelligence, I just want to make sure I'm not misunderstanding anything or assuming anything... The configuration of the switchport that the AP is connected to, is it set to trunk or Access and which vlans is it allowed to pass? I think you make reference to it using vlan1, so I'm going to assume that the AP and the client are on the same subnet, lets just say it's 192.168.1.0/24, and the default gateway is 192.168.1.1. I'm assuming that the DHCP server itself is on the same subnet, as you state that it is a local DHCP server, so lets just say that it's got an IP of 192.168.1.2. If the AP is on the same subnet, it is getting an IP of 192.168.1.3 (Assuming that the client and the AP are using the same Vlan/subnet, if not then the access port would need to be a trunk with allowed all or specific VLANs, but you said there was not L3 going on, but is that in reference to the wireless config??). You state that the client gets an IP, so lets say the client gets the IP 192.168.1.4. You said that it can't ping the DG (Which I've said is 192.168.1.1 in my example). I assume this is a router or firewall or something else. I'm also going to assume that the DNS values are NOT on the same subnet as everything else, lets set that too 192.168.2.2.

Some pings would assist. Can you ping the client from the DHCP server, or from the AP? Can you ping the DHCP or AP from the client? The 'No Internet' indicates that you can't route out to the internet, yet I'm assuming that you can from the DHCP server. Does the Default Gateway which is assigned to the client have any ACLs which restrict access out to the internet or any destination? I assume if you perform a traceroute out to 8.8.8.8 you get no response from any hops along the path from the client endpoint?

mikeschriver
Visitor

Glad to find this post but sad to see no resolve. Same thing happening on our Meraki AP's. AP's are setup with vlan tagging because we broadcast SSID's for multiple subnets for public, guest and corporate networks. Each with different DHCP servers. All do the same thing and only noticed it this year since school started and hundreds of kids teachers are on the network. Many report no WIFI connection just to report back 15 minutes later that they are connected. On the wireless DORA is sporadic. Some clients take right off others timeout and takes a few tries to get a successful IP.

My packet captures from a client, when the problem exists, show many DISCOVERS that continue until it either times out or finally gets an OFFER. Worked with Meraki support and they seem to think it's something in our switching. However I can hardwire the same client and DORA is instant every time. Besides no wired devices have the problem. I'm on the latest firmware but also tried an old firmware but problem is still there.

Very upsetting to not have an answer when Meraki has been so rock solid performing the past 10+ years we've had them. I cannot all of a sudden have 4 non-responsive DHCP servers on 4 different subnets doing the same thing for wireless clients only. The common denominator is the AP's.

If I find a solution I'll post here and hopefully others will do the same.

Hey, Maineiac15, did you find a fix for this issue? I am seeing the same issue at my school as well.

Unfortunately, no. We just have a band aid in place. Support as well as a hired engineering company couldn't figure it out. We got tired of the finger pointing and getting no where so implemented a temp fix. We placed a DHCP server right on the vlan for our student Chromebooks because that is the network with the largest number of devices which of course causes the most complaints. That has solved it for that one vlan.

Of course this doesn't solve it for all the other vlans but it solves 90% of the complaints. 😞

Review Cisco Networking for a $25 gift card