Hello everyone,I hope you are all doing well. I am seeking assistance regarding an issue I am facing with Cisco ACI.Context: I recently decommissioned a link and would like to remove all static ports associated with this link within Cisco ACI for cle...
Forum Posts
Device Version: /bootflash/aci-n9000-dk9.14.2.7g.bin Device Model: Cisco C9516 Problem description: As shown in the figure below, A cannot access B(any protocol), and after logging in to B and initiating a request from B to A(any protocol, we are ...
Resolved! ACI - License requirement
Hi, My N9k leaves have been shipped with the following licenses : ACI-N9K-48X -> ACI software license for a 48-port 1/10G Cisco Nexus 9000 Series switchACI-F48G -> ACI SW license for a 48p 1G Nexus 2K Do you have any informations to install the file...
Cisco ACI 4.2(7s)I want to see the contract deny packet logs appear in the System>Events window for troubleshooting purposes. It currently is not being presented.I know this works because I have it working in a different ACI environment. I've looked ...
We would like to integrate Microsoft azure peering service. We would like our Pod5 and Pod6 to be able to communicate with the Microsoft azure peering service. The two Pods are interconnected with each other through the IPN network. We have inter-...
Resolved! Multi-Site VMM VMware Integration
Hello Community!I am looking for guidance regarding a Cisco ACI multi-site design and VMM integration. There is one vcenter which manages hosts in both sites but, it also has DRS clusters configured across the two sites (DRS_A contains hosts from bot...
hi everyone, We are implementing a project and will integrate ACI with VMware NSX. I have a question: when integrating APIC with VMware NSX, is it necessary to first integrate with vCenter so that APIC automatically creates VDS, and then Integrate wi...
Hey Folks, I have an APIC cluster consists of 1 hardware APIC and 2 other Virtual APICs. I was looking for a command that shows if my two virtual APICs were installed as Vapic or as AVE (Cisco ACI Virtual Edge). I found the command `show fabric nodes...
Hi,After removing from controller the last spine from Pod 1 in a multi-pod fabric (version 5.2(7g)), what I have is Pod 2 and 3 having leafs and spines, and Pod 1 without any switch. At that moment I have a lot of interface tunnels on spines and leaf...
Good morning all!Looking at that pic and at this link I can add different devices to the same node profile and interface profile if i don't need to change BGP parameters as seen below. Moreover I can see i can "add" several subnets belonging to sev...
Resolved! Bidirectional ACI Contracts
I think I need assistance understanding the nuance of bi-directional subjects.We're doing a brownfield->greenfield migration. My securtity team requires me to block TFTP for all EPG-to-everywhere, except for specifically authorized exceptions; thank...
Logs are being observed in the Firewall where the source device that is not segmented is in a vlan that does not have an associated contract, which causes the traffic to goto the service graph.But there are many requests that should not be shown, rig...
Resolved! Cisco ACI Bug
Hello Team.I have the following question for anyone who can answer;In the process of loading images to update the ACI infrastructure equipment (specifically for the APIC controller), I get the following error "Request failed with status code 403", in...
HiI need to increase bandwidth for my leaf switches 101 and 102 to the spines. Can we add a second link from these leaf switches to the spines, while all other leaf switches maintain a single link to each spine?All the documentation seems to suggest ...
Has anyone got ACI Sim working on Proxmox ? I have unzipped the 5.2.4d OVA and then imported the OVF but when I try to start the VM it just hangs at: Booting Insieme Fabric Controller 5.2.4d on / rfs1 in 0 seconds ... I have assigned 64GB and 12 ...
