Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
I am playing around with enabling syslog in ACI and seeing what kinds of messages it sends out. I am not able to see it send out syslog messages however when someone changes its model via the ACI UI. The following web page describes how to config...
Do the active auto-discovery flows count as a licensed flow? My understanding is that those are flows that have not been fully set up to become optimized or pass-through. If I am licensed for 2500 concurrent connections, do the active auto-discovery...
I need to configure L3OUT between two tenants which are in the same ACI leaf node. Two tenants will be connected through a physical cable in the same ACI leaf node. Can it be configured? Please assist.
Device is displaying alarm: Major Alarms:------------- Alarm ID Module/Submodule Instance --------------- -------------------- --------------- 1 psu_ac_status sysmon/psu1_vinok no power Did a little more digging and found out that the hardw...
Hello everyone, I am working in an organization as network security officer. I am working with some providers, and we want to verify if the attribute "X-forwarded-for"is enable on our cisco ASA if not, to enable it. Can someone help me to find how to...
Hi All,My ACE module doesn not boot when i issue the reload command. Also no power enable module 7/power enable module 7 does not work. The only solution is to physically remove and re-insert the module on the switch.Please find the output of ACE mo...
Hi,Has anybody encountered wherein the WAAS device cannot be accesse via GUI but the device can be pinged, Also tried accessing it via CLI or attaching a Monitor or a keyboard on the device but the device does not respond if any key is pressed and no...
Could someone give me a steer please. I have a virtual F5 load balancer (VMM Domain is VMware). The VMM Domain is connected to my ACI and working for a number of VM's / Apps (excluding F5). Having installed the F5 VM and added OSPF to it, I wish...
I have two data centers running N7K/N5K/N2K. The N7K are VPC to N5K using VPC domain id 1 at both sites. The N5K to N2K use VPC domain id 2. I am getting the message: %PIM-4-DUP_VPC_NBR: pim [5418] Unexpected 2nd vPC peer xx.xx.xx.xx detected Som...
Dear all, I going to implement CISCO ACI network and wanted to connect on of MY HP5900 QSFP 40G uplink port on cisco ACI LEAF switch 9372 switch ....so can i Connect the HP switch Uplink port (QSFP) to cisco leaf switch 9372 QSFP port directly whethe...
Hi When I configure my WAAS there's a drop down box entitled "Interception method". The options available are None, WCCP, inline and appNav-controller. What method should I use if I want to use PBR to send traffic to the WAAS? I tried selecting ...
Hi!.Anybody knows something about this messages?We have ISR-4451 with ISR WAAS installed. These error messages are showed alot in the CLI 070502: Dec 8 10:35:08: %MDNSPROXY-3-API_FAIL_MDNS: Resolve Service API failed070503: Dec 8 10:35:09: %MDNSPROXY...
Hi, I have read: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/kb/b_KB_Transit_Routing.htmlI have 2 x border leaf switches into which I have 2 x separate L3 out connections. Both are in the same VRF. Layer 3 Out one goes t...
I am gettng the subject message when trying to sync my ACE modules. I am running A2(1.0a) right now (about to upgrade to 1.6a).Both primary and backup ACE report the identical output from a "show crypto files" down to the individual file sizes.Any ti...
Hi, Currently we are having 1G 8 port module installed in WAVE configured inline. We are planning to replace this module with 2 port 10g module . We need to know can this module be configured in line ? Thanks and Regards Pushpak
