Application Networking

Resolved! Upgrading to WAAS 5.4.1

HeyWe are planning to upgrade our environment (+250 devices) to the 5.4.1 version, and besides testing, we wanted to ask the community if anyone else completed the upgrade, and if so, any positive or negative experiences you want to share ?

WAAS express registration

I am trying to register a router licenced with waas express on our central manager.Within CM I am using Waas Express/RegistrationWhen I enter the details and select register I get the following status after a minute "Registration command is executed...

Configurable WCCP rotuer ID on ISR G1

Hi Team,is there any plan to add Configurable WCCP router ID feature for ISR G1 routers, please?Gratitude.Rgrds,Stan

Syslog error - WAAS-SYS-3-900000: e1000bp: eth5: e1000bp_clean_tx_irq: Detected Tx Unit Hang

I am receiving this error in my syslog, every couple weeks or so. It causes a flap between our two inline WAEs. Have an idea what can be causing this? syslog is below, start from the bottom up.2011-03-10 10:30:08 Kernel Error 10.0.100.26 2011 Mar 1...

WAAS EMAP Optimization issue

Dear Team, In WAAS Setup we are not seeing any Optimized EMAPI connection and below error is showing in Alarm section for all Edge WAE devices.Wansecure encountered a peering service configuration error: ssl peering service configuration mismatch wi...

Resolved! WAAS Central Manager

Hi All, Is anyone fully working on WAAS devices. I have a scenario, where our central manager's hard disk crashed but only the cms services have been disabled.I am not able to take backup of the config as we don't have any hard disk in it.Bad luck is...

How to update certificate into ACE

need to upload cert file (.pem) received fro CA and getting bellow error message: LB1# crypto import terminal wwwtest.domain.comPlease enter PEM formatted data. End with "quit" on a new line.-----BEGIN CERTIFICATE-----MIIG3zCCBcegAwIBAgIQS85KmZXhCY...

Resolved! initiating connections from the servers behind the ACE in a bridge context

We're running ACE A5(2.1) and have a server on a load balancing vlan in a bridge context that needs to initiate connections. Unlike servers in the routed contexts, where we had to SNAT their connections with the VIP, the client side and server side s...

Resolved! backup server on an ACE

When creating a backup server on an ACE running A5(2.1), we're using the probe as the trigger. Once the primary real server has failed to the backup, will it fail back to the primary server when the probe deems the primary server available?It's just...

How to view Tidal Job output in a query?

I am using a query to extract the standard output of a job:select jobrun_id, dbms_lob.substr( jobrun_output, 4000, 1 ) from tidal.joboutputwhere jobrun_id = 686361;The query returns output in an XML format:<TESXOUTPUT><MSG>Job output data is in XML ...

ACE 4710 software upgrade from A3(2.5) to A5(3.0)

HelloWe want our ACEs to support IPV6, we are currently using A3 2.5 and want to upgrade to A5 3.0 directly, is it possible? Or do I need to follow some other path before (like A4 and then A5)? The reason is because the network of the customer will b...

Resolved! TCP port Inheritance Question - Different URL to same VIP, same ServerFarm, different TCP port

Good Day All, My customer would like to have several different https URL with the same IP VIP address to be load-balanced to the same real servers listening to different TCP ports.I think cisco calls this option Port Inheritance.I am able to make the...

Resolved! ACE 4710 Non-LB traffic from real server

Hello,We are migrating from CSS to ACE and kind of hit a strange issue.On CSS when the real server (with internal address like 10.x.x.x) initiates its own connection to Internet for example check for Windows Updates the traffic goes to CSS (as it is ...

Resolved! logging into the user mode on the ACE

We're currently logging right into the enable mode when logging into the ACE30. Is there a way to log into a user mode and then use an enable password to get into the enable mode on the ACEs?Thanks.Greg....

WCCP with Layer2

Hi,I want to configure WCCP on Layer2 Redirection on Cisco Router 3800, but only GRE mode is working layer2 redirect is not comming up.Cisco Router Details: Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.4(15)T7, RELEASEProposed...

Application Networking

Forum Posts

Resolved! Upgrading to WAAS 5.4.1

WAAS express registration

Configurable WCCP rotuer ID on ISR G1

Syslog error - WAAS-SYS-3-900000: e1000bp: eth5: e1000bp_clean_tx_irq: Detected Tx Unit Hang

WAAS EMAP Optimization issue

Resolved! WAAS Central Manager

How to update certificate into ACE

Resolved! initiating connections from the servers behind the ACE in a bridge context

Resolved! backup server on an ACE

How to view Tidal Job output in a query?

ACE 4710 software upgrade from A3(2.5) to A5(3.0)

Resolved! TCP port Inheritance Question - Different URL to same VIP, same ServerFarm, different TCP port

Resolved! ACE 4710 Non-LB traffic from real server

Resolved! logging into the user mode on the ACE

WCCP with Layer2

VxLAN EVPN Multisite behavior for extended Vlans

DNAC node clusters on different subnets

WAE choses wrong loopback when building its IGP.

software-defined networks and software-defined data centers

Sustainability Survey - Survey Close

ACE module configuring NTP

cisco prime server

WAAS TCP Resets

SDN via API

Cisco data center courses