Application Networking

I am using the SSL probe script that Cisco provides. I would like to modify the script to send a "close connection" command to the server rather than just closing the socket on the CSM and leaving the server "hanging". Does anyone have any ideas on h...

Hi I have a CSS 11501 running 7.40 we are trying to get routing working through this port using ip management route x.x.x.x <Mask> Next HopWe can Ping the Next Hop but cannot get to the route end point. We have verified Layer 3 connectivity as we hav...

Hiwe have release 7.10.206a configured with SourceGroup and ASR. I made a sniffer trace and experienced that the CSS sends a lot of RST. As well I saw that it use only 1984 source ports for the connections to the server. How can I increase the number...

Hello all, A company I work for is hosting an application at a popular managed hosting provider and are using the css11501s to do layer-5 load balancing between a set of application servers. We are seeing a strange error that seems to occur when the ...

Guys,According to documentation only two CSS boxes can be configured for the same VIP in VIP redundancy mode (one active and one backup). However I can't find anything that can prevent addition of another pair CSS's in a backup mode for the same VIP....

Hi..My customer some GPRS user in which they couldn't control proxy setting of the web browser.Is it possible to configure on a cache engine such that when these users access the Internet, they will be intercepted by the cache engine. THe cache engin...

Hi,I'm facing problem with implementing WCCP on 7200 transparent mode with NetCache.The client are not able to access the internet. However if I hard code the client, I have no problem accessing the internet.Attached are the config that are currently...

Hi, I'm experiencing a slow response from my web servers via the CSM. After doing a sniffer trace it's show that the Vserver address does not reponse to the intial sync packet of the client but will only reponse to the second sync packets from the cl...

I have 4 6509s 2 are distribution and 2 are access…the 2 distro have a fwsm, ssl module, and a csm. The csm I have in bridge mode with default gateway as the fwsm, and almost all the services are an ssl offload. Now, Everything works great, but one p...

I have a CSS11501 load balancing 2 web servers. We want to use an Aventail in front of it as a reverse proxy, to control access to these servers. How can I ensure that the two servers will be load balanced, and make sure that an end user always hits ...

I have 2 servers being loadbalanced.Basic config.service telnet1ip address 192.168.1.1port 23protocol tcpactiveservice telnet2ip address 192.168.1.2port 23protocol tcpactiveowner telnetserverscontent telnetadd service telnet1add service telnet2vip ad...

Hello,We have 2 cat6513's with sup720's and csm's in FT mode.We have 3 sun webservers connected to the cat6513's using ipmp. Each server has two nic's, one nic connected to the primary switch and the other nic to the secondary switch.When I shutdown ...

Here is my issue:No source groups or udp.CSS Routed mode, version 7.4A client on the outside, say 1.1.1.1, sends a packet to the VIP of 2.2.2.2, the source port is 938 and the destination is 938.The VIP translates it to the 10 network (service) but s...

Can CSM-S w/SSL module work in Cat6K hybrid mode(CatOS&IOS)?Any other differences between CSM and CSM-S besides the SSL part?Thanks in advance.

Hi, My setup is as follow, I have 2 CSM in two different 6509 running in active and standby mode and 2 SSLM running also in two different 6509 too.My SSL traffic terminates at my SSLMCurrently my CSM and SSL is working fine but I notice there's this ...