01-17-2020 03:40 AM - edited 01-17-2020 03:42 AM
Hello
We are deploying DNA Wirelesss Assurance with 1800s sensors.
Sensors has been provisioned in DNA-C.
And simpe Test Suite has been scheduled.
But there is no results.
==========================================================
In sensor CLI:
AP70F3.5A7A.0198#show dot11 sensor stats ## Network Assurance Sensor Statistics ## WSA Status: Enabled NA Connectivity: Connected NA Connectivity I/F: Wired http NA Server URL: https://10.64.128.127 Auth Type: EAP HTTP Proxy IP: PROXY_IP Backhaul SSID: CiscoSensorProvisioning Id-token: Port: PORT Total Test Cases Run: 0 Successful Test Cases: 0 Failed Test Cases: 0 Network Assurance 5G Radio Statistics -------------------------- Host Rx K Bytes: 0 Host Tx K Bytes: 0 Unicasts Rx: 0 Unicasts Tx: 0 Broadcasts Rx: 0 Broadcasts Tx: 0 Beacons Rx: 0 Beacons Tx: 0 Multicasts Rx: 0 Multicasts Tx: 0 CRC errors: 0 Network Assurance 2G Radio Statistics -------------------------- Host Rx K Bytes: 0 Host Tx K Bytes: 0 Unicasts Rx: 0 Unicasts Tx: 0 Broadcasts Rx: 0 Broadcasts Tx: 0 Beacons Rx: 0 Beacons Tx: 0 Multicasts Rx: 0 Multicasts Tx: 0 CRC errors: 0 AP70F3.5A7A.0198# AP70F3.5A7A.0198#show dot11 sensor test config Test Config Received Time: 2020-01-17 10:47:30.604699 { advancedConfig: { rssiThreshold: -75 } testConfig: { targetAPs: testSuiteName: test-1 name: Onboarding bands: BOTH scheduleInDays: 0 connection: WIRELESS frequency: { value: 30 unit: MINUTES } ssids: { username: null validTo: 0 layer3webAuthsecurity: null numAps: 0 id: 0 authTypeRcvd: null authType: WPA2_PSK ssid: retail-service authProtocol: null eapMethod: null certxferprotocol: HTTP qosPolicy: null layer3webAuthpassword: **** psk: **** layer3webAuthuserName: null bands: BOTH layer3webAuthEmailAddress: null certfilename: null profileName: retail-service password: **** certstatus: ACTIVE wlc: 10.64.0.116 certpassphrase: null numSensors: 0 status: ENABLED certdownloadurl: null wlanId: 0 validFrom: 0 } startTime: 1579257944554 repeatCountOnFailure: 2 numberOfApsToTest: 3 wlans: retail-service testSuiteDetails: { BUILDING: Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266 AREAID: 32328f6c-3c7a-409a-8e74-6f6130743b8c TESTSUITENAME: test-1 FLOOR: Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266/1 AREA: Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439 FLOORID: ba56b83d-a535-4d33-bcc4-2cc45b04851f TESTSUITEID: 5e219058a61fa7002016a29f BUILDINGID: 307a9eff-c1c4-4074-b9bc-fc7db74c3ddf } config: {} type: DEDICATED testSuiteId: 5e219058a61fa7002016a29f:!_ba56b83d-a535-4d33-bcc4-2cc45b04851f:!_Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266/1:!_307a9eff-c1c4-4074-b9bc-fc7db74c3ddf:!_Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266:!_32328f6c-3c7a-409a-8e74-6f6130743b8c:!_Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439:!_test-1 } wlans: { username: null validTo: 0 layer3webAuthsecurity: null numAps: 0 id: 0 authTypeRcvd: null authType: WPA2_PSK ssid: retail-service authProtocol: null eapMethod: null certxferprotocol: HTTP qosPolicy: null layer3webAuthpassword: **** psk: **** layer3webAuthuserName: null bands: BOTH layer3webAuthEmailAddress: null certfilename: null profileName: retail-service password: **** certstatus: ACTIVE wlc: 10.64.0.116 certpassphrase: null numSensors: 0 status: ENABLED certdownloadurl: null wlanId: 0 validFrom: 0 } } AP70F3.5A7A.0198#show dot11 sensor test results AP70F3.5A7A.0198#
NTP has been configured via CLI
AP70F3.5A7A.0198#show ntp NTP server Stratum Version Last Received Delay Offset Jitter time.moscow.spo 2 4 1827sec ago 0.000ms 0.000ms 0.000ms
As you see test suite is configured on sensor but there is no result
Please help to troubleshoot this issue?
Thanks.
Solved! Go to Solution.
01-20-2020 06:45 AM
You are running old sensor code which isn't recommended since DNAC version 1.2.10. Please attempt to upgrade at least 8.8.263.0:
-- https://software.cisco.com/download/home/286318948/type/286288051/release/8.8.263.0
Since your 1800s sensor has already been claimed and in your DNA center inventory, you can use SWIM to upgrade the software on the sensor from the DNA center GUI.
01-17-2020 07:34 AM
What DNAC version do you have deployed?
What version is the 1800s running?
01-19-2020 08:54 PM
Hello
1800s Running Image : 8.8.259.0
DNAC maglev, version 1.3.0.3938
sensor-assurance Assurance - Sensor 1.4.0.484
01-19-2020 11:07 PM - edited 01-19-2020 11:13 PM
As i see test suits does not run on to the sensors
01-20-2020 06:45 AM
You are running old sensor code which isn't recommended since DNAC version 1.2.10. Please attempt to upgrade at least 8.8.263.0:
-- https://software.cisco.com/download/home/286318948/type/286288051/release/8.8.263.0
Since your 1800s sensor has already been claimed and in your DNA center inventory, you can use SWIM to upgrade the software on the sensor from the DNA center GUI.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide