02-02-2021 09:06 AM
Hi, I suspect my terminal servers are no longer supported but I'm hoping to try to recover one that cannot remember it's config. The problem was detected when our lab was taken offline and physically moved across town.
The solution I was going to try is to load a different version of OS because I found that as a possible solution to a similar issue online. But I can't find a link to download the OS.
Am open to try other things if anyone has a different idea.
Thanks!
Marshall Kelly
Ribbon (formerly Genband) Communications
Router#write
Building configuration...
[OK]
NVRAM Verification Failed
Router#show version
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-I-L), Version 11.2(5)P, SHARED PLATFORM, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1997 by cisco Systems, Inc.
Compiled Mon 07-Apr-97 11:52 by tej
Image text-base: 0x030229F8, data-base: 0x00001000
ROM: System Bootstrap, Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
ROM: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
Router uptime is 3 days, 21 hours, 22 minutes
System restarted by power-on
System image file is "flash:c2500-i-l.112-5.P", booted via flash
cisco AS2511-RJ (68030) processor (revision I) with 2048K/2048K bytes of memory.
Processor board ID 08394789, with hardware revision 00000000
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
16 terminal line(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read ONLY)
Configuration register is 0x2102
02-02-2021 09:12 AM
try below methods :
02-02-2021 09:28 AM
Thanks you Balaji but that didn't help. Still seeing the issue.
Router#copy running-config startup-config
Building configuration...
[OK]
NVRAM Verification Failed
Router#show startup-config
%% Non-volatile configuration memory has not been set up
02-02-2021 09:48 AM
Can you post output of below :
show version
dir
try
#wr memory
02-02-2021 10:15 AM
02-02-2021 10:37 AM - edited 02-02-2021 10:39 AM
Try
#show flash
Router#dir Translating "dir"...domain server
Please post show run
02-02-2021 10:44 AM
02-02-2021 10:57 AM - edited 02-02-2021 11:01 AM
before i suggest some stuff. can you post show run (this was asked before also) and dir nvram:
02-02-2021 11:01 AM
02-02-2021 11:02 AM
end
Router#dir nvram
^
% Invalid input detected at '^' marker.
02-02-2021 11:30 AM
dir isn't valid in this release apparently.
Router>en
Password:
Router#?
Exec commands:
access-enable Create a temporary Access-List entry
access-template Create a temporary Access-List entry
bfe For manual emergency modes setting
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
connect Open a terminal connection
copy Copy configuration or image data
debug Debugging functions (see also 'undebug')
disable Turn off privileged commands
disconnect Disconnect an existing network connection
enable Turn on privileged commands
erase Erase flash or configuration memory
exit Exit from the EXEC
help Description of the interactive help system
lock Lock the terminal
login Log in as a particular user
logout Exit from the EXEC
mbranch Trace multicast route down tree branch
mrbranch Trace reverse multicast route up tree branch
mrinfo Request neighbor and version information from a multicast
router
mstat Show statistics after multiple multicast traceroutes
mtrace Trace reverse multicast path from destination to source
name-connection Name an existing network connection
no Disable debugging functions
pad Open a X.29 PAD connection
ping Send echo messages
ppp Start IETF Point-to-Point Protocol (PPP)
reload Halt and perform a cold restart
resume Resume an active network connection
rlogin Open an rlogin connection
rsh Execute a remote command
send Send a message to other tty lines
setup Run the SETUP command facility
show Show running system information
slip Start Serial-line IP (SLIP)
start-chat Start a chat-script on a line
systat Display information about terminal lines
telnet Open a telnet connection
terminal Set terminal line parameters
test Test subsystems, memory, and interfaces
traceroute Trace route to destination
tunnel Open a tunnel connection
undebug Disable debugging functions (see also 'debug')
verify Verify checksum of a Flash file
where List active connections
write Write running configuration to memory, network, or terminal
x3 Set X.3 parameters on PAD
02-02-2021 12:09 PM
show nvrom - correct syntax.
02-02-2021 12:19 PM
Thanks but show nvrom doesn't seem valid in this release.
Router#show nvrom
^
% Invalid input detected at '^' marker.
Router#
Router#show ?
WORD Flash device information - format <dev:>[partition]
access-expression List access expression
access-lists List access lists
accounting Accounting data for active sessions
aliases Display alias commands
arp ARP table
async Information on terminal lines used as router interfaces
bridge Bridge Forwarding/Filtering Database [verbose]
buffers Buffer pool statistics
cdp CDP information
clock Display the system clock
cmns Connection-Mode networking services (CMNS) information
compress Show compression statistics
configuration Contents of Non-Volatile memory
controllers Interface controller status
debugging State of each debugging option
dhcp Dynamic Host Configuration Protocol status
dialer Dialer parameters and statistics
dnsix Shows Dnsix/DMDP information
dxi atm-dxi information
entry Queued terminal entries
flash System Flash information
flh-log Flash Load Helper log buffer
frame-relay Frame-Relay information
history Display the session command history
hosts IP domain-name, lookup style, nameservers, and host table
interfaces Interface status and configuration
ip IP information
key Key information
line TTY line information
llc2 IBM LLC2 circuit information
location Display the system location
logging Show the contents of logging buffers
memory Memory statistics
modemcap Show Modem Capabilities database
ntp Network time protocol
ppp PPP parameters and statistics
printers Show LPD printer information
privilege Show current privilege level
processes Active process statistics
protocols Active network routing protocols
queue Show queue contents
queueing Show queueing configuration
registry Function registry information
reload Scheduled reload information
rhosts Remote-host+user equivalences
rif RIF cache entries
rmon rmon statistics
route-map route-map information
running-config Current operating configuration
sessions Information about Telnet connections
smds SMDS information
smf Software MAC filter
snapshot Snapshot parameters and statistics
snmp snmp statistics
spanning-tree Spanning tree topology
stacks Process stack utilization
standby Hot standby protocol information
startup-config Contents of startup configuration
subsys Show subsystem information
tacacs Shows tacacs+ server statistics
tcp Status of TCP connections
tech-support Show system information for Tech-Support
terminal Display terminal configuration parameters
traffic-shape traffic rate shaping configuration
users Display information about terminal lines
version System hardware and software status
whoami Info on current tty line
x25 X.25 information
x29 X.29 information
Router#show
02-02-2021 12:33 PM
Apologies, i worked on 2511 for more than 15 years now.
I suggest fixing the issue.(not sure if that work, if not we may need to erase NVRAM and startup from scratch - i will guide if the below steps not working)
this is test it able to write :
config t
!
service compress-config
!
boot config flash:
!
end
wr
post the outcome.
02-02-2021 12:46 PM
No apologies necessary. I've worked with these 2500s or over 20 years. They just work (most of the time).
It didn't like the line -> boot config flash:
but the write was successful
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#serv
Router(config)#service comp
Router(config)#service compress-config
Router(config)#boot config ?
% Unrecognized command
Router(config)#boot config flash
^
% Invalid input detected at '^' marker.
Router(config)#boot config flash:
^
% Invalid input detected at '^' marker.
Router(config)#end
Router#
%SYS-5-CONFIG_I: Configured from console by consolewr
Building configuration...
Compressing configuration from 650 bytes to 476 bytes
[OK]
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide