07-02-2009 11:59 PM - edited 03-12-2019 09:20 AM
Because the 6.0(1) release of Cisco Unified Communications Manager uses a different installation framework than previous releases of Cisco Unified Communications Manager, review all installation instructions carefully before you install Cisco Unified Communications Manager 6.0(1).
This guide includes information about installing Cisco Unified Communications Manager Release 6.0(1) on one server or many servers in a cluster environment.
For information about upgrading from a Windows-based release (4.x) of Cisco Unified Communications Manager to an appliance-based release (5.0 and higher), refer to Upgrading Cisco Unified Communications Manager.
Note: This guide describes only the first two installation types: Basic Install and Upgrade During Install. For information on performing a Windows Upgrade, refer to Upgrading Cisco Unified CallManager.
Before you proceed with the Cisco Unified Communications installation, consider the following requirements and recommendations:
• Be aware that when you install on an existing server, the hard drive gets formatted, and all existing data on the drive gets overwritten.
• Install the Cisco Unified Communications Manager software on the first node or publisher server first and then on the subsequent nodes.
• Make sure that the subsequent node servers that you are installing can connect to the first node server during the installation.
• Enter the same security password on all servers in the cluster.
• Install the Cisco Unified Communications Manager software during off-peak hours or a maintenance window to avoid impact from interruptions.
• Configure the server by using static IP addressing to ensure that the server obtains a fixed IP address and that the Cisco Unified IP Phones can register with the application when you plug the phones into the network.
• Do not attempt to perform any configuration tasks during the installation.
• Do not install any Cisco-verified applications until you complete the installation of Cisco Unified Communications Manager.
• Directory names and filenames that you enter while running the installation program are case-sensitive.
• Carefully read the instructions that follow before you proceed with the installation
The following section contains information about commonly asked questions and responses. Review this section carefully before you complete the Cisco Unified Communications Manager installation.
How long does it take to perform the Cisco Unified Communications Manager installation? The entire installation process, excluding pre- and post-installation tasks, takes 45 to 90 minutes per server, depending on your server type. Before you install Cisco Unified Communications Manager, consider the size of your cluster.
What Passwords do I Need to Specify? During the Cisco Unified CallManager installation, you must specify the following user names and passowords:
• Administrator account
You use the Administrator username and password to log in to the following areas:
– Cisco Unified Communications Operating System Administration
– Disaster Recovery System
– Command Line Interface
The Administrator login must start with an alphabetic character, be at least six characters long, and can contain alphanumeric characters, hyphens, and underscores. You can change the Administrator password or add a new Administrator account by using the command line interface. See the Cisco Unified Communications Operating System Administration Guide for more information.
• Application User password
You use the Application User password for the following default application user names:
– CCMAdministrator
– CCMSysUser
– WDSysUser
– CCMQRTSysUser
– IPMASysUser
– WDSecureSysUser
– CCMQRTSecureSysUser
– IPMASecureSysUser
You can change the application user password for each application through Cisco Unified CallManager Administration. See the Cisco Unified CallManager Administration Guide for more information.
• Database Access Security Password
The system uses this password to authorize communications between nodes, and you must ensure that this password is identical on all nodes in the cluster.
The Database Access Security password must start with an alphanumeric character, be at least six characters long, and can contain alphanumeric characters, hyphens, and underscores.
Which servers does Cisco support for this installation? For information about the supported servers, refer to the release notes for your version of Cisco Unified CallManager. Click here for Cisco Product Release Notes.
May I install other software besides Cisco Unified CallManager on the server? You must do all software installations and upgrades by using Cisco Unified Communications Operating System Administration. The system can upload and process only software that Cisco Systems approved.
You cannot install or use third-party or Windows-based software applications that you may have been using with a previous version of Cisco Unified Communications Manager with Cisco Unified Communications Manager 6.0(1).
You can access Cisco Unified CallManager Administration, Cisco Unified CallManager Serviceability, and Cisco Unified Communications Administration by using the following browsers:
• Microsoft Internet Explorer version 6.0 or later
• Netscape Navigator version 7.1 or later
Note: Cisco does not support or test other browsers, such as Mozilla Firefox.
As a part of software installation, the system installer configures the system BIOS and RAID settings for the new operating system and Cisco Unified CallManager application. See Table 2 for the BIOS settings and Table 3 for the RAID settings that are set up during installation.
Note: If the hardware configuration process fails during installation, you can use boot-time utilities that are found on both the IBM and HP servers to manually configure the RAID and BIOS settings, as shown in Table 2 and Table 3.
Table 2 BIOS Configuration Settings for HP and IBM Servers
HP Servers | IBM Servers |
OS Selection: Linux (not applicable on newer models) | OS Selection: Not Applicable |
Boot Order: CD, C:, Floppy | Boot Order: CD, C:, Floppy |
Post F1 prompt: Delayed | Post F1 prompt: Delayed |
Hyperthreading: Enabled | Hyperthreading: Enabled |
Table 3 RAID Settings
MCS 7825 Servers (HP and IBM) | MCS 7835 Servers (HP and IBM) | MCS 7845 Servers (HP and IBM) |
Software Raid | Logical Drives: 1 | Logical Drives: 2 |
Software Raid Note For the HP 7825H1 and the IBM 7825I1, SATA RAID is enabled, and the RAID type specifies 1(1+0), with one logical drive | RAID type: 1(1+0) | RAID type: 1(1+0) |
For more detailed descriptions of each installation field, see Table 4.
Use Table 4 to record the information about your Cisco Unified CallManager server. Gather this information for each Cisco Unified CallManager server that you are installing in the cluster. You may not need to obtain all the information; gather only the information that is pertinent to your system and network configuration. You should make copies of this table and record your entries for each server in a separate table, even if you are planning to use the DMABackupInfo.inf file to configure your system.
Note: Because some of the fields are optional, they may not apply to your configuration. For example, you choose not to set up an SMTP host.
Caution: You cannot change some of the fields after installation without reinstalling the software, so be sure to enter the values that you want.
The last column in the table shows whether a field can be changed after installation, and if so, whether you can change it through Cisco Unified Communications Operating System Administration or through the Command Line Interface (CLI).
Table 4 Configuration Data
Configuration Data | Your Entry | Can Entry Be Changed After Installation |
Administrator Password | Yes. CLI> set password admin | |
Application User Password | Yes. CLI> set password | |
Country | Yes. CLI>set web-security | |
DHCP | Yes. CLI> set network dhcp | |
DNS Primary | Yes. CLI>set network dns | |
DNS Secondary | Yes. CLI>set network dns | |
Domain | Yes. CLI>set network domain | |
Domain Name Service DNS Enable | NO. | |
Gateway Address | Yes Use OS Adminstration > Settings>IP | |
Host Name | NO. | |
IP Address | Yes Use OS Adminstration > Settings>IP | |
IP Mask | Yes Use OS Adminstration > Settings>IP | |
Location | Yes. CLI>set web-security | |
Master Administrator ID | NO. | |
NTP Server IP Address Note You can enter up to five NTP servers. | Yes Use OS Administration > Settings>NTP Servers | |
Organization | Yes CLI> set web-security | |
Security Password | Yes CLI> set password security | |
SMTP Location | Yes CLI> set smtp | |
State | Yes CLI> set web-security | |
Time Zone | Yes CLI> set timezone | |
Unit | Yes CLI> set web-security |
For more detailed descriptions of each installation field, see Table 5.
Table 5 Installation Field Definitions
Field | Description | Usage |
Administrator ID | This field specifies the name that you want to assign to this account. | Ensure the name is unique; it can contain lowercase, alphanumeric characters, hyphens, and underscores. It must start with a lowercase alphanumeric character. |
Administrator Password | This field specifies the password that you use for logging into the the CLI on the platform and for logging into Cisco Unified Communications Operating System Administration. | Ensure the password is at least six characters long; it can contain alphanumeric characters, hyphens, and underscore. |
DHCP | Dynamic Host Configuration Protocol | Choose Yes if you want to use DHCP to automatically configure the network settings on your server. |
DNS Enabled | A DNS server represents a device that resolves a hostname into an IP address or an IP address into a hostname. | If you do not have a DNS server, enter No. When DNS is not enabled, you should only enter IP addresses (not hostnames) for all network devices in your Cisco Unified Communications network. |
DNS Primary | The server contacts this DNS server first when it attempts to resolve host names. | Enter the IP address of the DNS server that you want to specify as the primary DNS server. Enter the IP address in dotted decimal format as ddd.ddd.ddd.ddd where ddd can have a value between 0 and 255 (except 0.0.0.0). |
DNS Secondary | When a primary DNS server fails, the server will attempt to connect to the secondary DNS server. | In this optional field, enter the IP address of the secondary DNS. Enter the IP address in dotted decimal format as ddd.ddd.ddd.ddd where ddd can have a value between 0 and 255 (except 0.0.0.0). |
Domain | This field represents the name of the domain in which this machine is located. | Consider this field mandatory if DNS is set to yes. |
First Cisco Unified Communications Manager Node | This field specifies the first Cisco Unified Communications Manager node that contains the database. | Choose Yes if you are configuring the first Cisco Unified Communications Manager node in the cluster. |
Gateway Address | A gateway represents a network point that acts as an entrance to another network. Outbound packets get sent to the gateway that will forward them to their final destination. | Enter the IP address of the gateway in the format ddd.ddd.ddd.ddd where ddd can have a value between 0 and 255 (except 0.0.0.0) |
Host Name | A host name represents an alias that is assigned to an IP address to identify it. | Enter a host name that is unique to your network. |
IP Address | This field specifies the IP address of this machine. It will uniquely identify the server on this network. Ensure another machine in this network does not use this IP address. | Enter the IP address in the form ddd.ddd.ddd.ddd where ddd can have a value between 0 and 255 (except 0.0.0.0). |
IP Mask | This field specifies the IP subnet mask of this machine. The subnet mask together with the IP address define the network address and the host address. | Enter the IP mask in the form ddd.ddd.ddd.ddd where ddd can have a value between 0 and 255 (except 0.0.0.0). |
NIC Speed | This field specifies the speed of the server network interface card (NIC) in megabits per second. | The possible speeds include 10 or 100. |
NIC Duplex | This field specifies the duplex setting of the server NIC. | The possible settings include half and full. |
NTP Server | This field identifies the NTP servers with which you want to synchronize. | Enter the hostname or IP address of one or more NTP server(s). |
NTP Server Enable | When enabled, this server will act as a NTP server and provide time updates to the subsequent nodes in the cluster. | Choose Yes if you want to enable this machine to be an NTP server. |
Security Password | Servers in the cluster use the security password to communicate with one another. | Enter the security password. Enter the same password in the confirm password field. Caution You must enter the same password for all nodes in the cluster. |
Set Hardware Clock | This field specifies the date and local time for the machine. Note If you set the hardware clock manually, the node does not use an external NTP server for time synchronization. | Choose Yes if you want to set the date and local time for the time zone that you chose. |
SMTP | This field specifies the name of the SMTP host that is used for outbound e-mail. | Enter the hostname or dotted IP address for the SMTP server. For a host, it can contain alphanumeric characters, hyphens, or periods. For a host name, it must start with an alphanumeric character. You must fill in this field if you plan to use electronic notification. If not, you can leave it blank. |
Subnet IP Address | By entering a subnet address, you can specify a range of IP Addresses that will be granted access to query this NTP server. | Enter an IP subnet that will be granted access to the NTP server |
Subnet Mask | This field specifies the subnet mask for the subnet address. | Enter the subnet mask for the IP subnet. |
Time zone | This field specifies the local time zone and offset from Greenwich Mean Time (GMT). | Choose Yes if you want to change the time zone. |
Cisco Unified Communications Answer File Generator, a web application, generates answer files for unattended installations of Cisco Unified Communications Manager Business Edition. Individual answer files get copied to a USB key or a floppy diskette that accompanies the Cisco Unified Communications Manager Business Edition DVD during the installation process.
The web application supports the following features:
• Allows simultaneous generation and saving of answer files for unattended installs on the publisher server and all subscriber servers.
• Provides syntactical validation of data entries.
• Provides online help and documentation.
The following usage requirements apply:
• The web application supports only fresh installs (for example, it does not include upgrades).
• If DHCP client is being used on the publisher server, and subscriber server answer files are also being generated, you must specify the publisher server IP address.
You can access the Cisco Unified Communications Answer File Generator at the following URL:
http://www.cisco.com/web/cuc_afg/index.html
The Cisco Unified Communications Answer File Generator supports Internet Explorer version 6.0 or higher and Mozilla version 1.5 or higher.
If a USB key is being used to perform an unattended installation of Cisco Unified Communications Manager Business Edition, you may need to reformat the USB key to the FAT32 file system beforehand. You need to reformat especially in the case of USB keys with larger storage capacity (for example, 1 Gigabyte) that are formatted with the FAT file system.
You can use the Windows XP Disk Management Utility to reformat a USB key to the FAT32 file system as follows (you might need to be logged in as an administrator or a member of the Administrators group to perform these tasks):
Procedure
Step 1 Insert the USB key into a USB slot on the Windows XP PC.
Step 2 Choose Start > Control Panel > Administrative Tools and then double-click Computer Management.
Step 3 Expand the Storage tree and click Disk Management.
Step 4 Right-click the Removable Disk icon and click Format.
Step 5 You may be asked whether you are sure that you want to format this partition; click Yes.
Step 6 Click the File System: pull down and select FAT32.
Step 7 Click OK. When prompted to format the volume, click OK again.
The Removable Disk icon text should now show the file system format as FAT32.
During the installation process, the installation program verifies that the server can successfully connect to the network by using the network configuration you enter. If it cannot, a message displays, and you get prompted to select one of the following options:
• RETRY — The installation program tries to validate networking again. If validation fails again, the error dialog box displays again.
• REVIEW (Check Install)— Allows you to review and modify the networking configuration. The installation program returns to the network configuration windows.
Networking gets validated after you complete each networking window, so the message might display multiple times. If the message displays while you are reviewing the network configuration windows, choose IGNORE to move to the next window. If you choose REVIEW, the first network configuration window displays again.
• HALT — The installation halts. You can copy the installation log files to a USB disk to aid troubleshooting of your network configuration.
• IGNORE — The installation continues. The networking error gets logged. In some cases, the installation program validates networking multiple times, so this error dialog box might display multiple times. Note: Networking is validated after you complete each networking window, so the message might display multiple times. If the message displays while you are reviewing the
network configuration windows, choose IGNORE to move to the next window. If you choose REVIEW, the first network configuration window appears again.
NOTE: This document describes only the first two installation types: Basic Install and Upgrade During Install. For information on performing a Windows Upgrade, refer to Upgrading Cisco Unified Communications Manager.
Step 1 Insert the installation DVD into the tray and restart the server, so it boots from the DVD. After the server completes the boot sequence, the DVD Found window displays.
Step 2 To perform the media check, choose Yes, or to skip the media check, choose No. The media check checks the integrity of the DVD. If your DVD has passed the media check previously, you might choose to skip the media check.
Note: If you have a new server with Cisco Unified Communications Manager Business Edition preinstalled, you do not need to install from a DVD, unless you want to reimage the server with a later product release. You can go directly to the "Entering Preexisting Configuration Information" procedure.
Step 3 If you choose Yes to perform the media check, the Media Check Result window displays. Perform these tasks: a. If the Media Check Result displays Pass, choose OK to continue the installation.
b. If the media fails the Media Check, either download another copy from Cisco.com or obtain another disc directly from Cisco.
Step 4 The system installer performs the following hardware checks to ensure that your system is correctly configured. If the installer makes any changes to your hardware configuration settings, you will get prompted to restart your system. Leave the DVD in the drive during the reboot:
• First, the installation process checks for the correct drivers, and you may see the following warning:
No hard drives have been found. You probably need to manually choose device drivers for install to succeed. Would you like to select drivers now?
To continue the installation, choose Yes.
• The installation next checks to see whether you have a supported hardware platform. If your server does not meet the exact hardware requirements, the installation process fails with a critical error. If you think this is not correct, capture the error and report it Cisco support.
• The installation process next verifies RAID configuration and BIOS settings.
NOTE: If this step repeats, choose Yes again.
After the hardware checks complete, Product Deployment Selection window displays.
Step 5 In the Product Deployment Selection window, select the product to install; then, choose OK. You can choose from the following options:
• Cisco Unified Communications Manager
• Cisco Unity Connection
• Cisco Unified Communications Manager Business Edition (includes Cisco Unified Communications Manager and Cisco Unity Connection)
NOTE: Only the products that are supported on your server appear in the list.
Step 6 If software is currently installed on the server, the Overwrite Hard Drive window opens and displays the current software version on your hard drive and the version on the DVD. Choose Yes to continue with the installation or No to cancel.
CAUTION: If you choose Yes on the Overwrite Hard Drive window, all existing data on your hard drive gets overwritten and destroyed.
The Platform Installation Wizard window displays.
Step 7 To configure the platform now, choose Proceed. If you want to configure the platform later, choose Skip.
• If you want to install and configure the software at this time, choose Proceed and continue with this procedure.
• If you want to install the software now and configure it later or if you have a server that has Cisco Unified Communications Manager Business Edition preinstalled, choose Skip and continue with the "Entering Preexisting Configuration Information" section.
Step 8 Choose the type of installation to perform by doing the following steps. See Table 6 for more information on installation options:
a. In the Apply Additional Release window, choose one of the options:
• To upgrade to a later Service Release of the software during installation, choose Yes. Continue with the "Upgrading During Installation" section.
• To skip this step, choose No.
• To return to the previous window, choose Back.
b. In the Import Windows Data window, choose No.
NOTE: To perform a Windows Upgrade, that is, to upgrade from a Windows version of Cisco Unified Communications Manager to Cisco Unified Communications Manager 6.0(1), see Upgrading Cisco Unified Communications Manager for more information.
Step 9 In the Basic Install window, choose Continue to install the software version on the DVD or configure the preinstalled software. Continue with the "Performing the Basic Installation" section.
Start here if you have a server that has the product preinstalled or if you chose Skip in the Platform Installation Wizard window.
Step 1 After the system restarts, the Preexisting Installation Configuration window displays.
Step 2 If you have preexisting configuration information, generated by the Answer File Generator, that is stored on a floppy disc or a USB key, insert the disc or the USB key now and choose Continue. The installation wizard will read the configuration information during the installation process.
Step 3 To continue with the Platform Installation Wizard, choose Proceed.
Step 4 Choose the type of installation to perform by doing the following steps. See Table 6 for more information on installation options:
a. In the Apply Additional Release window, choose one of the options:
• To upgrade to a later Service Release of the software during installation, choose Yes. Continue with the "Upgrading During Installation" section.
• To skip this step, choose No.
• To return to the previous window, choose Back.
b. In the Import Windows Data window, choose No.
NOTE: To perform a Windows Upgrade, that is, to upgrade from a Windows version of Cisco Unified Communications Manager to Cisco Unified Communications Manager 6.0 see Upgrading Cisco Unified Communications Manager for more information.
Step 5 In the Basic Install window, choose Continue. Continue with the "Performing the Basic Installation" section.
If you choose Yes in the Upgrade During Install window, the installation wizard installs the software version on the DVD first and then restarts the system. You must obtain the appropriate upgrade file from Cisco.com before you can upgrade during installation.
If you are upgrading from Cisco Unified Communications Manager release 5.x, the upgrade file name has the following format:
cisco-ipt-k9-patchX.X.X.X-X.tar.gz.sgn Where X.X.X.X-X represents the release and build number.
NOTE: Do not rename the patch file before you install it because the system will not recognize it as a valid file. NOTE: Do not unzip or untar the file. If you do, the system may not be able to read the upgrade files.
If you are upgrading from Cisco Unified Communications Manager release 6.x, the upgrade file has the extension sgn.iso.
You can access the upgrade file during the installation process from either a local disk (CD or DVD) or from a remote FTP or TFTP server.
: Step 1 After the system restarts, the Platform Installation Wizard window displays. To continue the installation, choose Proceed.
The Upgrade During Install window displays.
NOTE: If the installer pops up a window that states that it detected new hardware, press any key and then choose Install from the next window.
Step 2 Choose Yes.
: Step 3 Choose the upgrade retrieval mechanism to use to retrieve the upgrade file:
• SFTP — Retrieves the upgrade file from a remote server by using the Secure File Transfer Protocol (SFTP). Skip to the "Upgrading from a Remote Server" section.
• FTP — Retrieves the upgrade file from a remote server by using File Transfer Protocol (FTP). Skip to the "Upgrading from a Remote Server" section.
• LOCAL — Retrieves the upgrade file from a local CD or DVD. Continue with the "Upgrading from a Local Disk" section.
Before you can upgrade from a local disk, you must download the appropriate patch file from Cisco.com and copy the file to a CD or DVD. Because of the size of the patch files, you will need to copy it to a DVD in most cases.
•If you are using an upgrade file with the tar.gz.sgn extension, copy the upgrade file to a writeable CD or DVD.
•If you are using an upgrade file with the sgn.iso extension, you must create an ISO image on the DVD from the upgrade file.
Step 1 When the Local Patch Configuration window displays, enter the patch directory and patch name, if required, and choose OK.
NOTE: You only need to enter the patch directory when the patch is not stored in the root directory of the CD or DVD. If the patch is stored in the root directory, enter a slash (/) in the directory field. NOTE: This step does not apply if you are using an upgrade file with the sgn.iso extension.
The Install Upgrade Patch Selection Validation window displays.
Step 2 The window displays the patch file that is available on the CD or DVD. To update the system with this patch, choose Continue.
Step 3 Choose the upgrade patch to install. The system installs the patch, then restarts the system running the upgraded software version.
After the system restarts, the Preexisting Configuration Information window displays. Skip to the "Entering Preexisting Configuration Information" section.
If you chose to upgrade through an FTP or SFTP connection to a remote server, you must first configure the network settings.
Step 1 The Auto Negotiation Configuration window displays.
Step 2 The installation process allows you to automatically set the speed and duplex settings of the Ethernet network interface card (NIC) by using automatic negotiation. You can change this setting after installation.
• To enable automatic negotiation, choose Yes. The DHCP Configuration window displays.
NOTE: To use this option, your hub or Ethernet switch must support automatic negotiation.
•To disable automatic negotiation, choose No. The NIC Speed and Duplex Configuration window displays.
Step 3 If you chose to disable automatic negotiation, manually choose the appropriate NIC speed and duplex settings now and choose OK to continue.
The DHCP Configuration window displays.
Step 4 For network configuration, you can choose to either set up static network IP addresses for the node and gateway or to use Dynamic Host Configuration Protocol (DHCP).
• If you have a DHCP server that is configured in your network and want to use DHCP, choose Yes. The system restarts and checks for network connectivity. Skip to Step 7.
• If you want to configure static IP addresses for the node, choose No. The Static Network Configuration window displays.
Step 5 If you chose not to use DHCP, enter your static network configuration values and choose OK. See Table 5 for field descriptions.
The DNS Client Configuration window displays.
Step 6 To enable DNS, choose Yes, enter your DNS client information, and choose OK. See Table 5 for field descriptions.
After the system configures the network and checks for connectivity, the Remote Patch Configuration window displays.
Step 7 Enter the location and login information for the remote file server. See Table 5 for field descriptions. After the network restarts, the system connects to the remote server and retrieves a list of available upgrade patches.
If the upgrade file is located on a Linux or Unix server, you must enter a forward slash at the beginning of the directory path. For example, if the upgrade file is in the patches directory, you must enter /patches. If the upgrade file is located on a Windows server, check with your system administrator for the correct directory path.
The Install Upgrade Patch Selection window displays.
Step 8 Choose the upgrade patch to install. The system downloads, unpacks, and installs the patch and then restarts the system running the upgraded software version.
After the system restarts, the Preexisting Configuration Information window displays. Continue with the "Entering Preexisting Configuration Information" section.
Step 1 When the Timezone Configuration displays, choose the appropriate time zone for the server and then choose OK.
The Auto Negotiation Configuration window displays.
Step 2 The installation process allows you to automatically set the speed and duplex settings of the Ethernet network interface card (NIC) by using automatic negotiation. You can change this setting after installation.
• To enable automatic negotiation, choose Yes. The DHCP Configuration window displays.
NOTE: To use this option, your hub or Ethernet switch must support automatic negotiation.
• To disable automatic negotiation, choose No. The NIC Speed and Duplex Configuration window displays.
Step 3 If you chose to disable automatic negotiation, manually choose the appropriate NIC speed and duplex settings now and choose OK to continue.
The DHCP Configuration window displays.
Step 4 For network configuration, you can choose to either set up static network IP address for the node or to use Dynamic Host Configuration Protocol (DHCP).
• If you have a DHCP server that is configured in your network and want to use DHCP, choose Yes. The network restarts, and the Administrator Login Configuration window displays.
• If you want to configure static IP address for the node, choose No. The Static Network Configuration window displays.
Step 5 If you chose not to use DHCP, enter your static network configuration values and choose OK. See Table 5 for field descriptions.
The DNS Client Configuration window displays.
Step 6 To enable DNS, choose Yes, enter your DNS client information, and choose OK. See Table 5 for field descriptions.
The network restarts by using the new configuration information, and the Administrator Login Configuration window displays.
Step 7 Enter your Administrator login and password from Table 4.
NOTE: The Administrator login must start with an alphabetic character, be at least six characters long, and can contain alphanumeric characters, hyphens, and underscores. You will need the Administrator login to log in to Cisco Unified Communications Operating System Administration, the command line interface, and the Disaster Recovery System.
The Certificate Information window displays.
Step 8 Enter your certificate signing request information and choose OK.
The First Node Configuration window displays.
Step 9 You can configure this server as either the first node in a Cisco Unified Communications Manager cluster or as a subsequent node.
• To configure this server as the first Cisco Unified Communications Manager node, choose Yes and continue with the "Configuring the First Node" section.
• To configure this server as a subsequent node in the cluster, choose No and continue with the "Configuring a Subsequent Node" section.
After you finish the basic installation, follow this procedure to configure the server as the first node in the cluster.
Step 1 The Network Time Protocol Client Configuration window displays.
Cisco recommends that you use an external NTP server to ensure accurate system time on the first node. Ensure the external NTP server is stratum 9 or higher (meaning stratums 1-9). Subsequent nodes in the cluster will get their time from the first node.
Step 2 Choose whether you want to configure an external NTP server or manually configure the system time.
• To set up an external NTP server, choose Yes and enter the IP address, NTP server name, or NTP server pool name for at least one NTP server. You can configure up to five NTP servers, and Cisco recommends that you use at least three. Choose Proceed to continue with the installation.
The system contacts an NTP server and automatically sets the time on the hardware clock.
NOTE: If the Test button displays, you can choose Test to check whether the NTP servers are accessible.
• To manually configure the system time, choose No and enter the appropriate date and time to set the hardware clock. Choose OK to continue with the installation.
The Database Access Security Configuration window displays.
Step 3 Enter the Database Access Security password from Table 4.
NOTE: The Database Access Security password must start with an alphanumeric character, be at least six characters long, and can contain alphanumeric characters, hyphens, and underscores. The system uses this password to authorize communications between nodes, and you must ensure this password is identical on all nodes in the cluster.
The SMTP Host Configuration window displays.
Step 4 If you want to configure an SMTP server, choose Yes and enter the SMTP server name.
NOTE: You must configure an SMTP server to use certain platform features; however, you can also configure an SMTP server later by using the platform GUI or the command line interface.
Step 5 Choose OK. The Application User Configuration window displays.
Step 6 Enter the Application User Username and Password from Table 4 and confirm the password by entering it again.
Step 7 Choose OK. The Platform Configuration Confirmation window displays.
Step 8 To continue with the installation, choose OK; or to modify the platform configuration, choose Back.
The system installs and configures the software. The DVD drive ejects and the server reboots. Do not reinsert the DVD.
Step 9 When the installation process completes, you get prompted to log in by using the Administrator account and password.
Step 10 Complete the post-upgrade tasks that are listed in the "Post-Installation Tasks" section.
To configure a subsequent node in the cluster, follow these steps.
CAUTION: You must configure a subsequent node on the first node using Cisco Unified Communications Manager Administration before you install the subsequent node. For more information, see the Cisco Unified Communications Manager Administration Guide.
Step 1 The First Node Access Configuration window displays.
Step 2 Enter the First Node Access Configuration information from Table 4.
The SMTP Host Configuration window displays.
Step 3 If you want to configure an SMTP server, choose Yes and enter the SMTP server name.
NOTE: You must configure an SMTP server to use certain platform features. However, you can also configure an SMTP server later by using the platform GUI or the command line interface.
The Platform Configuration Confirmation window displays.
Step 4 To start installing the software, choose OK, or, if you want to change the configuration, choose Back.
Step 5 When the installation process completes, you get prompted to log in by using the Administrator account and password.
Step 6 Complete the post-upgrade tasks that are listed in the "Post-Installation Tasks" section
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: