This document was generated from CDN thread
Created by: Jeevan Varughese on 07-05-2010 10:30:26 PM
Hi There,
Was hoping you could assist with the following:
I have a client who currently has two tandberg Precision HD Cameras that connect to a Tandberg Video Switch which in turn feeds a Tandberg 6000 MXP.
The way it is hooked up is the Precision HD cameras daisy chain together (control) and each output HDMI Video into the video ports of the Tandberg Video Switch. The Tandberg 6000 is in turn controlled by a Control system using RS-232.
Is it possible to setup presets on Tandberg camera #1 and Tandberg Camera #2 using the remote control and then recall them on the tandberg remote control?
If yes, if I am on camera # 1, and i recall a preset that is mapped to a position for Camera #2, does the video automatically switch or do i have to switch the video using the softbuttons on the remote control?
I was also curious to know if its possible to control a visca camera (Sony EviD70) using the tandberg Remote and setup presets on it.
I am hoping you can assist me with the following:
1)
Is it possible to setup presets on Tandberg camera #1 and Tandberg Camera #2 using the remote control and then recall them on the tandberg remote control?
If yes, if I am on camera # 1, and i recall a preset that is mapped to a position for Camera #2, does the video automatically switch to Camera #2 on the Tandberg Video Switch or do i have to switch the video using the softbuttons on the remote control?
What I am looking to do is give the client the ability to move the camera to a preset location and then when ready, use the soft buttons to switch to the second camera after it has already moved.
2)
If supported, I would like to hook up a third-party camera Sony EVId70 SD Camera (svideo output) to the AUX Svideo input of the Tandberg 6000 and have the VISCA control of this camera hooked into port #2 of the Tandberg Video swtich. I would like to call up this camera using the "AUX" softbutton on the TRC4 Remote. I would like to control the camera using the tandberg remote. Currently the visca control cable is terminated to control port #2 of the Tandberg Video Switch (it is controlled by the control system)
IF also possible, i would like to setup 3 preset positions that can be recalled using the Tanbderg remote.
(if the above is not supported, I would replace this with a Tandberg HD precision Camera and add it to the control chain of cameras. I would then like to call up this camera using the "DVD" softbutton and assign three preset positions to it that can be recalled using the TAndberg Remote)
.
I have attached some logs that I captured from the Tandberg 6000 using the following commands and hoping this assists:
1) Xstatus Camera
2) Xstatus Switch
I also did an xconfig on the tandberg 6000 and the below information is what is currently listed for the xconfig logical input section of the log:
*c xConfiguration Switch Source: 1
*c xConfiguration Switch Configuration Primary: On
*c xConfiguration Switch Configuration Secondary: On
*c xConfiguration Switch LogicalInput 1 Mode: On
*c xConfiguration Switch LogicalInput 1 Map: 1
*c xConfiguration Switch LogicalInput 2 Mode: Off
*c xConfiguration Switch LogicalInput 2 Map: 2
*c xConfiguration Switch LogicalInput 3 Mode: On
*c xConfiguration Switch LogicalInput 3 Map: 2
*c xConfiguration Switch LogicalInput 4 Mode: Off
*c xConfiguration Switch LogicalInput 4 Map: 1
*c xConfiguration Switch LogicalInput 5 Mode: Off
*c xConfiguration Switch LogicalInput 5 Map: 5
Ive attached the extended setting from TMS on the Tandberg 6000 in question if you need more than the above.
The software running on the codec is F6.2 . I didnt want to upgrade it as it is connected to a control system and was unsure if this would effect the communcation between the control processor and Tandberg 6000 Data Port (RS-232)
If there is anything else I can provide please let me know.
Regards
Jeevan
