cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
300944
Views
227
Helpful
31
Comments
Lang Hardison
Cisco Employee
Cisco Employee

     

    CUCM Database Replication is an area in which Cisco customers and partners have asked for more in-depth training in being able to properly assess a replication problem and potentially resolve an issue without involving TAC.  This document discusses the basics needed to effectively troubleshoot and resolve replication issues.

     

     

    Replication Architecture

    CUCM 5.x Replication Architecture

    Communications Manager 5.x has a similar replication topology to Callmanager 4.X. They both follow a hub and spoke topology. The publisher establishes a connection to every server in the cluster and the subscribers establish a connection the local database and the publisher only. As illustrated in the figure below, only the publisher's database is writable while each subscriber contains a read only database. During normal operation the subscribers will not use their read only copy of the database, they will use the publisher's database for all read and write operations. In the event the publisher goes down or becomes inaccessible the subscribers will use their local copy of the database. Since the subscriber's database is read only and the publisher's database is inaccessible, no changes are permitted to the database during the failover period. Changes in architecture are implemented in later versions to address this limitation.

    5xreplication.png

     

     

    CUCM 6.x-10.x Architecture

    Replication in Communications Manager 6.x, 7.x, and 8.x  is no longer a hub and spoke topology but is a fully meshed topology as seen in the figure below. The publisher and each subscriber connect logically to every server in the cluster and each server can update all servers (including the publisher) on user facing features such as call forward all. The full list of user facing features is located on the following slide.  This change in topology overcomes previous limitations in replication architecture, as changes can now be made to local subscriber databases for user facing faetures even while the publisher is inaccessible. Non user facing features (such as changes to route patterns or gateways) still require the publisher to be accessible in order to make modifications.

    6xreplication.png

     

    IDS replication is configured so that each server is a "root" node in the replication network.  Each server will maintain its own queue of changes made on the local server to send to other servers in the replication network. A root node will not pass a replication change on to another root node. Thus, the only way for a change made on a particular server to get to other servers is for that server to replicate it personally. In other words, a change made on "A" will be sent to "B" by "A". But, "B" will not send that same change on to "C". Server "A" must send it to "C" and all other nodes.
    User Facing Features


    Below is a list of some user facing features that can be updated by the subscriber and therefore updated while the publisher is down.   This is not an exhaustive list.

     

    User Facing Features

    Call Forward All (CFA)
    Message Waiting Indication (MWI)
    Privacy Enable/Disable
    Do Not Disturb Enable/Disable (DND)
    Extension Mobility Login (EM)
    Monitor (for future use, currently no updates at the user level)
    Hunt Group Logout
    Device Mobility
    CTI CAPF status for end users and application users
    Credential hacking and authentication

     

     

    Checking Current Replication Status

     

    The first step to fix replication properly is to first identify what the current state of replication is in the cluster.  Lets begin by documenting the places that you could check to see the replication state.

     

    The Real Time Monitoring Tool - Database Summary Page


    In RTMT, Choose CallManager->Service->Database Summary.

    RTMT-DatabaseSummary.png


    Cisco Unified Reporting - Database Status Report


    Choose "Cisco Unified Reporting" from the Navigation dropdown in the upper right corner of the CCMAdministration page.  Then choose "Database Status Report", and generate a new report.

     

    DatabaseStatusReport.png

     

    CLI Commands to Check Replication State

    admin:show perf query class "Number of Replicates Created and State of Replication"
    ==>query class :
    - Perf class (Number of Replicates Created and State of Replication) has instances and values:
        ReplicateCount  -> Number of Replicates Created   = 348
        ReplicateCount  -> Replicate_State                = 2
    runtimestatestatus.png

     

    What does the Status (0,1,2,3,4) Mean?

    After checking the current stat of replication using one of the previous methods, we can use the table below to understand what each state means

    ValueMeaningDescription
    0 Initialization State This state indicates that replication is in the process of trying to  setup. Being in this state for a period longer than an hour could  indicate a failure in setup.
    1 Number of Replicates not correct This state is rarely seen in 6.x and 7.x but in 5.x can indicate its  still in the setup process. Being in this state for a period longer than  an hour could indicate a failure in setup.
    2 Replication is good Logical connections have been established and tables match the other servers on the cluster.
    3 Tables are suspect

    Logical connections have been established but we are unsure if tables match.

    In 6.x and 7.x all servers could show state 3 if one server is down in  the cluster.

    This can happen because the other servers are unsure if  there is an update to a user facing feature that has not been passed  from that sub to the other device in the cluster.

    4 Setup Failed / Dropped The server no longer has an active logical connection to receive  database table across. No replication is occurring in this state.

     

     

    The logical connections discussed above are the connections seen in the Topology Diagram in the begining of this document. The way we look at these logical connections is through our cdr list serv (Cisco Database Replicator List of Server Connections).

    Verifying the Status Number Based on Descriptions

    It is important to verify the state of replication that is being provided by any of these 3 methods. For example, in some instances a server could show that it is in state 3 but the 'cdr list serv' output shows that the logical connections  are in "Dropped" state. This is similar to the server being in state 4.  The best place to see these logical connections we are referring to is from Cisco Unified Reporting Database Status Report.  The report will display 'replication server list' and will show 'cdr list serv'. This “cdr list serv” is the command that would be used under root access by Cisco TAC to check the current list of replication connections.

    Note:
    Cisco Database Replicator (CDR) list of servers is in no way related to Call Detail Records (also known as CDR).
    Ciso Unified Reporting - Replication Server List (cdr list serv)

    serverlist.png

    Next Steps

    Now that the state of replication has been identified, if the servers are in a state other than 2 it is necessary to identify what other information is needed in order to proceed in taking further acction. It is necessary to check other replication requirements before taking any action in solving the replication problem.  Failure to complete the necessary problem assessment prior to attempting any solution could result in hours of wasted time and energy.

    Server/Cluster Connectivity

    Confirm the connectivity between nodes. In 5.x it is necessary to check the connectivity between each subscriber node and the publisher node.  In 6.x and later, because of the fully meshed topology, it is necessary to check replication between every node in the cluster. This is important to keep in mind if an upgrade has taken place from 5.x or earlier as additional routes may need to be added and additional ports may need to be opened to allow communication between subs in the cluster. The documentation on checking connectivity is linked below.

    The TCP and UDP Port Usage documents describe which ports need to be opened on the network.

    CUCM 8.5:

    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/port/8_5_1/portlist851.html

    CUCM 8.0:

    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/port/8_0_2/portlist802.html

    Configuration Files

    Check all the hosts files that will be used when setting up replication. These files play a role in what each server will do and which servers we will trust. The files we are referring to here are listed below

     

     

    FilePurpose

    /etc/hosts This file is used to locally resolve hostnames to IP addresses.  It should include the hostname and IP address of all nodes in the cluster including CUPS nodes.
    /home/informix/.rhosts A list of hostnames which are trusted to make database connections
    $INFORMIXDIR/etc/sqlhosts Full list of CCM servers for replication.  Servers here should have the correct hostname and node id (populated from the process node table).  This is used to determine to which servers replicates are pushed.

     

    /etc/hosts

    Below is the /etc/hosts as displayed Verified in Unified Reporting. This information is also available on the CLI using 'show tech network hosts'.  Cluster Manager populates this file and is used for local name resolution.

     

    etchosts.png

    .rhosts file
    rhosts.PNG
    sqlhosts

    sqlhosts.PNG

     

    DNS (Optional)

    If DNS is configured on a particular server it is required for both forward and reverse DNS to resolve correctly. Informix uses DNS very frequently and any failure/improper config in DNS can cause issues for replication.

     

    Verifying  DNS

    The best command to verify DNS is utils diagnose test. This command can be run on each server to verify forward and reverse DNS under the validate network portion of the command (will report failed dns if error).   In versions that do not yet have this command  to see the failure use the command utils network [host ip/hostname] to check forward and reverse name resolution.

    diagnosetest.png

    Using Replication Commands

    Meaning of each command

    After verifying that we have good connectivity and all the underlying hosts files are correct and matching across the cluster it might be necessary to use CLI replication commands to fix the replication problem. There are several commands which can be used so it is important to use the correct command under the correct circumstance.   The following table lists each command and it's function.  Certain commands are not available in each version of CUCM.

     

    commandfunction

    utils dbreplication stop

    Normally run on a subscriber. Stops currently replication running, restarts A Cisco DB Replicator, deletes marker file used to signal replication to begin. This can be run on each node of the cluster by doing “utils dbreplication stop”.

    In 7.1.2 and later “utils dbreplication stop all” can be run on the Publisher node to stop replication on all nodes

    utils dbreplication repair  

    utils dbreplication repairtable

    utils dbreplication repairreplicate

    Introduced in 7.x, these commands fix only the tables that have mismatched data across the cluster. This mismatched data is found by issuing a utils dbreplication status. These commands should only be used if logical connections have been established between the nodes.
    utils dbreplication reset Always run from the publisher node, used to reset replication connections and do a broadcast of all the tables. This can be executed to one node by hostname “utils dbreplication reset nodename” or on all nodes by “utils dbreplication reset all”.
    utils dbreplication quickaudit Checkes critical dynamic tables for consistency.  To check all tables run utils dbreplication status.
    utils dbreplication clusterreset

    Always run from the publisher node, used to reset replication connections and do a broadcast of all tables. Error checking is ignored. Following this command 'utils dbreplication reset all' should be run in order to get correct status information. Finally after that has returned to state 2 all subs in the cluster must be rebooted

    Note:  This command is no longer functional as of CUCM 9.0(1).  Use "utils dbreplication reset all" instead.

    utils dbreplication runtimestate Available in 7.X and later this command shows the state of replication as well as the state of replication repairs and resets. This can be used as a helpful tool to see which tables are replicating in the process.
    utils dbreplication forcedatasyncsub This command forces a subscriber to have its data restored from data on the publisher.  Use this command only after the 'utils dbreplication repair' command has been run several times and the 'utils dbreplication status' ouput still shows non-dynamic tables out of sync.
    utils dbreplication dropadmindb Run on a publisher or subscriber, this command is used to drop the  syscdr database. This clears out configuration information from the  syscdr database which forces the replicator to reread the configuration  files. Later examples talk about identifying a corrupt syscdr database.
    utils dbreplication dropadmindbforce Same as above, but may need to be used in cases where above command fails
    utils dbreplication setprocess Sets the "process" value within Informix.  This enables multithreading and improves replication setup time at the slight cost of processing power.  Recommended to set to 40 for large clusters (10+ nodes). 

     

     

    Examples

    Reestablish logical CDR connections to all servers for replication

    Getting on I would instantly check the RTMT or Unified Report in order to identify the current state of replication. I choose to ask for the Database Status report as the customer is in a version that has this available. In the report the information I find is the following.

     

    • The cluster is a 5 node cluster.
    • The publisher is in Replication State = 3
    • All subscribers in the cluster are in  Replication State = 4
    • We check in the report for Replication Server List and only the publisher shows local as connected. This verifies to us that based on our descriptions the servers are indeed in the states listed above.
    • We now do some other checks to prepare to fix replication. We verify in the report that all of the hosts files look correct. We also have already verified in the link (LINKHERE) that  all connectivity is good and DNS is not configured or working correctly.

     

    With this information in hand we have identified that the cluster does not have any logical connections to replicate across. Thus the recommendation to the customer would be to follow the most basic process that fixes about 50 percent of replication cases. Below are these steps.

     

    1. utils dbreplication stop on all subscribers. This command can be run on all subscribers at the same time but needs to complete on all subscribers prior to being run on the publisher. The amount of time this command takes to return is based on your cluster's repltimeout. This can be seen through the Command show tech repltimeout and by default is 300 seconds or 5 minutes. At the end of this document I will provide a calculation for determining what you should set your repltimeout (via utils dbreplication setrepltimeout) in your cluster and how this value affects replication.  (If utils dbreplication stop all is available (7.X and later) then step 1 and step 2 can be accomplished in this one command)
    2. utils dbreplication stop on publisher.  Again this command can be done through the utils dbreplication stop all if available.  This also will wait the repltimeout as said above.
    3. utils dbreplication reset all - This command will take an hour to complete or longer depending on your cluster. You can monitor the status through the utils dbreplication runtimestate or through the procedure following the examples portion of this document.

     

    Reestablish logical CDR connection to a single node

     

    Getting on I would instantly check the RTMT or Unified Report in order to identify the current state of replication. I choose to ask for the Database Status report as the customer is in a version that has this available. In the report the information I find is the following.

     

    • The cluster is a 3 node cluster.
    • The publisher is in  Replication State = 3
    • SubscriberA is in Replication State =3 and SubscriberB is in   Replication State = 4
    • We check in the report for Replication  Server List and  the publisher shows local as connected and SubscriberA as connected. Subscriber B is not listed in this list (NOTE* Would be the same procedure if SubscriberB showed "Dropped". This  verifies to us that based on our descriptions the servers are indeed in  the states listed above.
    • We now do some other checks to prepare  to fix replication. We verify in the report that all of the hosts files  look correct. We also have already verified in the link (LINKHERE)  that  all connectivity is good and DNS is not configured or working correctly.
    1. utils dbreplication stop on Subscriber B. This  command can be run on all subscribers at the same time but needs to  complete on all subscribers prior to being run on the publisher. The  amount of time this command takes to return is based on your cluster's  repltimeout. This can be seen through the Command show tech  repltimeout and by default is 300 seconds or 5 minutes.
    2. utils  dbreplication reset nodename from publisher. In our example I would type utils dbreplication stop subscriberB from the publisher and then wait for it to recreate the logical connection to the subscriberB and broadcast the tables to that subscriber. To follow where in the procedure it is you can use utils dbreplication runtimestate or the procedure following the examples section.
    3. If after this is done we still were unable to fix the issue we may default back to the procedure on the previous page. (utils dbreplicaton stop all from publisher (or on subs then pub) and then utils dbreplication reset all)

    Logical connections are established but tables are out of sync

    Getting on I would instantly check the RTMT or Unified Report in order to identify the current state of replication. I choose to ask for the Database Status report as the customer is in a version that has this available. In the report the information I find is the following.

     

    • All nodes in the cluster are in Replication State = 3
    • We check in the  report for Replication  Server List and all servers show as connected in the list (each server shows local for itself but connected from other servers perspective) This  verifies to us that based on our descriptions  the servers are indeed in  the states listed above.
    • We now do  some other checks to prepare  to fix replication. We verify in the  report that all of the hosts files look correct. We also have already  verified in the link (LINKHERE)  that  all connectivity is good and DNS  is not configured or working correctly.

     

    1. utils dbreplication status from publisher.  This command will confirm for us that indeed we have mismatched tables. Based on our earlier explanations this means that we do not need to do any reset as they fix connections and repairs fix mismatched tables. Once we have used the status to confirm that we have tables different we then can proceed to fix.
    2. utils dbreplication repair from publisher -  Which repair command depends on which tables and how many tables are out of sync. If you have a megacluster or a very large deployment a repair can take a long time (a day in some instances depending on how it failed) Thus it is important on which command you pick in those circumstances. On smaller deployments (less than 5,000 phones for example a utils dbreplication repair all is normally fine to do. If it is only one node with a bad table we can do utils dbreplication repair nodename. If it is only one table you can use utils dbreplication repairtable (node/all) to fix it on the problem server or on the whole cluster.

     

    Corrupt syscdr causing replication failure

    • The cluster is a 3 node cluster.
    • The publisher is  in  Replication State = 3
    • SubscriberA is in Replication State =3  and SubscriberB is in   Replication State = 4
    • We check in the  report for Replication  Server List and  the publisher shows  local as connected and SubscriberA as connected. Subscriber B is not  listed in this list (NOTE* Would be the same procedure if SubscriberB  showed "Dropped". This  verifies to us that based on our descriptions  the servers are indeed in  the states listed above.
    • We now do  some other checks to prepare  to fix replication. We verify in the  report that all of the hosts files  look correct. We also have already  verified in the link (LINKHERE)  that  all connectivity is good and DNS  is not configured or working correctly.
    Here are the things we tried utils dbreplication stop on Subscriber Butils  dbreplication reset SubscriberB from publisher. When that still failed we then tried utils dbreplication stop all, followed by utils dbreplication reset all.  After this we waited for an hour and our status's have once again reverted back to Replication State = 3 for publisher and SubscriberA with SubcriberB in state 4. Our Replication Server List again shows that we do not have a connection to SubscriberB even after using the reset commands to try and reset up that connection. With that the question becomes What do I do now?
    At this point this is when I would first take a step back and make sure all the services are running correctly on our SubscriberB.  From the CLI of subscriberB I would then confirm that the following services are started using the command utils service list (A CIsco DB, A Cisco DB Replicator, Cisco Database Layer Monitor). If any issues with these services we must first work on getting those to start (try manually via utils service start servicename). If everything is ok there then we need to confirm if syscdr (the underlying component for replication could be corrupt). In order to do this please run a utils dbreplication status from the problem node SubscriberB. From the output at the top we will be looking or 2 different distinct states.
    1. Enterprise Replication not active 62 - Normal state means that replication has not yet been defined on the node
    2. ---------------------------------------------   Dashes only at the top of the output. This could indicate a corrupt  syscdr. This output  can only be checked from the utils dbreplication  status command as the Cisco Unified Reporting Tool Database Status  Report displays just ------------------------ for both of the above  states (CSCti84361 as been opened to address that issue).
    If from the utils dbreplicaton status you do see you are currently in state 2 above (shows just ----------------------------- header without any servers listed) here is what you need to do to fix that issue. If the following does not resolve the issue you will probably need a tac case to resolve.
    1. utils dbreplication stop - Issued on SubscriberB
    2. utils dbreplication dropadmindb - Issued on SubscriberB to  restart the syscdr on that node.
    3. utils dbreplication reset <subscriberB> - TO once again try to reestablish the connection after fixing the corrupted syscdr.

    Replication Steps

    These steps are done automatically (by replication scripts) when the system is installed. When we do a “utils dbreplication reset all” they get done again.

     

    List of steps

     

    Define Pub - Set it up to start replicating

    Define template on pub and realize it (Tells pub which tables to replicate)

    Define each Sub

    Realize Template on Each Sub (Tells sub which tables they will get/send data for)

    Sync data using "cdr check" or "cdr sync" (older systems use sync)

     


    Replication Flow Chart

    Replicationflow.jpg

    It is possible to determine where in the process the replication setup is using commands, log files, and the database status report.

    This command utils dbreplication runtimestate is most helpful in identifying the current runtimestate of replication setup. In versions where that is not available or as a supplement here is how to follow replication using logs.
    Publisher syscdr/define
    Confirm that publisher has brought its on syscdr back up (In Cisco Unified Reporting-> Database Status -> Replication Server List confirm that you see the publisher's local connection up. This should occur within a few minutes of the reset. You can also look in the informix log on that box to confirm this.  "file view activelog cm/log/informix/ccm.log" from CLI
    Publisher Define

    srisivarpubdefines-syscdr.jpg

     

    Subscriber define

     

    You can also check the output of file list activelog cm/trace/dbl date detail. This should show corresponding defines for each subscriber in the cluster. *Note*: Publisher define not listed here.

    The define is shown in white below.

     

     

     

    definebroadcastlisted.png

     

    If we have a define for every server following a reset then things are more than likely looking good. Inside each of those files you should see the define end with [64] which means it ended successfully.

     

    definelog.jpg

     

     

     

    After all subscribers have been defined we then wait the repltimeout (Can check from show tech repltimeout) it will then do a broadcast file that actually pushes the replicates across. The broadcast is shown in yellow. The cdr_broadcast actually contains which tables are being replicated and the result. Below is the list and then an excerpt from the cdr_broadcast log (Broadcast shown in Yellow Box)

     

    definebroadcastlisted.png

    CDR Broadcast Log Excerpt

    broadcastfileexpanded.jpg

     

    With this you should be able to follow and fix replication cases. Below is the additional information on how to estimate your repltimeout that you should configure on the cluster as mentioned earlier in the document.

     

     

    Replication Timeout Design Estimation


    Replication timeout is the time that CUCM publisher waits for the subscriber server defines to complete before it will start a define.  

     

    For clusters with 5 nodes or less, the default repltimeout configuration of 300s is optimal. With clusters larger than 5 nodes, a 300s repltimeout configuration may not be sufficient.  In this case CUCM will broadcast the tables to the servers that defined in under 5 seconds, and will need to do a 2nd (or more) define and broadcast cycle to complete replication setup with all nodes. 

     

    THe following guideline provides recommended intervals for repltimeout for configuration based on the number of nodes in the cluster:

     

    Server 1-5 = 1 Minute Per Server

    Servers 6-10  = 2 Minutes Per Server

    Servers >10 = 3 Minutes Per Server.

     

    Example: 12 Servers in Cluster : Server 1-5 * 1 Min = 5 Min, + 6-10 * 2 Min = 10 min, + 11-12 * 3 Min = 6 Min, 

    Repltimeout should be set to 21 Minutes.

     

    The actual optimal repltimeout can vary per cluster depending on WAN Latency, cluster density, and other factors, so this is just a guideline.

     

    To confirm that replication is setting up in a single batch, run utils dbreplication stop all followed by utils dbreplication reset all from the CUCM publisher, and then verify the sequence of logs using file list activelog cm/trace/dbl/* date detailed from the publisher CLI. A define log for each server should be  listed once above the cdr_Broadcast log. 

     

    Note:

    Starting in CUCM 10.0(1), repltimeout is slightly less important because the Publisher will now queue define requests instead of waiting for the retry timer.  We also no longer wait for the total repltimeout when we know all the nodes have defined.  Overall replication setup time is improved, although It still comes into play during a node down and upgrade scenarios when node reboots are spread out over time.

     

    Document Contributors:

    =========

    Russ Hardison (rhardiso)

    Sriram Sivaramakrishnan (srsivara)

    Wes Sisk (wsisk)

    Ryan Ratliff (rratliff)

    Jason Burns (jasburns)

    Kenneth Russel (kerussel)

    Omar Mora (ommora)

    Shane Kirby (shkirby)

    Special thanks to Nancy Balsbaugh. 
    Comments
    George Sotiropoulos
    Cisco Employee
    Cisco Employee

    Amazing collection of information

     

    Thank you

    G

    Getting Started

    Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: