cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
12662
Views
0
Helpful
1
Replies

%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED

hoangkinleo
Level 1
Level 1

Hi everyone,

Could someone help me with the problem below? I wanted to add new VLANs 60 & 61 but they are suspended/disallowed over the Peer Link or the Trunk, Does anyone of you have experience in this issue please help?

7K4(config)# show vpc consistency-parameters global

Name                        Type  Local Value            Peer Value            

-------------               ----  ---------------------- -----------------------

STP Mode                    1     Rapid-PVST             Rapid-PVST           

STP Disabled                1     None                   None                 

STP MST Region Name         1     ""                     ""                   

STP MST Region Revision     1     0                      0                    

STP MST Region Instance to  1                                                 

VLAN Mapping                                                                 

STP Loopguard               1     Enabled                Enabled              

STP Bridge Assurance        1     Enabled                Enabled              

STP Port Type, Edge         1     Normal, Disabled,      Normal, Disabled,    

BPDUFilter, Edge BPDUGuard        Enabled                Enabled              

STP MST Simulate PVST       1     Enabled                Enabled              

Interface-vlan admin up     2     20,80,211,280,283,901- 20,80,211,280,283,901-

                                  903                    903                  

Interface-vlan routing      2     20,70,80,211,280,283,9 20,70,80,211,280,283,9

capability                        01-903                 01-903               

Allowed VLANs               -     10-13,20,24,60-61,70,8 10-13,20,24,70,80,156,

                                  0,156,211,278,280-286, 211,278,280-286,901-90

                                  901-903,3000           3,3000               

Local suspended VLANs       -     60-61  

*********************************************************************************************************

#Show logging

2016 Jun 16 08:02:35 7K4 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 60-61

on Interface port-channel3012 are being suspended. (Reason: Vlan is not allowed

on Peer-link)

2016 Jun 16 08:02:35 7K4 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 60-61

on Interface port-channel3011 are being suspended. (Reason: Vlan is not allowed

on Peer-link)

2016 Jun 16 08:02:35 7K4 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 60-61

on Interface port-channel3010 are being suspended. (Reason: Vlan is not allowed

on Peer-link)

2016 Jun 16 08:02:35 7K4 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 60-61

on Interface port-channel1101 are being suspended. (Reason: Vlan is not allowed

on Peer-link)

2016 Jun 16 08:02:35 7K4 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 60-61

on Interface port-channel1051 are being suspended. (Reason: Vlan is not allowed

on Peer-link)

2016 Jun 16 08:02:35 7K4 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 60-61

on Interface port-channel1050 are being suspended. (Reason: Vlan is not allowed

on Peer-link)

**********************************************************************************************************

#show interface trunk

Port          Vlans Err-disabled on Trunk

--------------------------------------------------------------------------------

Eth4/2        60-61

Eth4/4        60-61

Eth4/6        60-61

Eth4/8        60-61

Po1000        60-61

Po1050        60-61

Po1051        60-61

Po1101        60-61

Po3010        60-61

Po3011        60-61

Po3012        60-61

Eth101/1/30   60-61

Eth101/1/43   60-61

Eth101/1/44   60-61

Eth101/1/45   60-61

Eth101/1/46   60-61

Eth101/1/47   60-61

Eth101/1/48   60-61

1 Reply 1

slstefan
Level 1
Level 1

Hi there,

Vlans 60-61 are suspended because they are only allowed on the peer-link end of the local switch, but they weren't allowed on the peer switch also - so they're suspended due to vPC config inconsistency. Take another look at the "show vpc consistency-parameters global" output you have provided and you will notice that:

Allowed VLANs

     Local Value:

10-13,20,24,60-61,70,80,156,211,278,280-286,901-903,3000

     Peer Value: 

10-13,20,24,70,80,156, 211,278,280-286,901-903,3000

After fixing the allowed vlans mismatch, you'll see them removed from the suspended vlans list; if you don't - pls share the vPC related running config.

Cheers!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: