Greetings! I have couple of /24 overlay based networks on a nexus 7K switch. The route to these overlay networks is through 2 Edge software routers that are in ECMP How do i configure same destinaitonnetwork routes with equal weight pointed at th...
Forum Posts
Hi, Nexus 7K S1 has CMP port. I am wondering anyone had performed NX-OS software upgrade remotely through CMP like a console port. Thanks.
Hi Vlan 900 exists in the switch4500 and it is native. it shows "Spanning tree instance(s) for vlan 900 does not exist" when using command "show spanning-tree vlan 900. Why is that? by command show run | b spanning, we can see "spanning-tree vlan 1-...
Some ports of my nexus sport to work, I checked the log and collected this messages: 2018 Aug 8 11:43:11 swa.001 %PLATFORM-2-MOD_REMOVE: Module 2 removed (Serial number JAE18160R11)2018 Aug 8 11:43:13 swa.001 %PLATFORM-2-MOD_DETECT: Module 2 detect...
Hi all here is my scenario that I'm looking to get some feedback on and in my opinion this might be part of some issues: - 2 NX 7K's. - Peer Keep alive links, vPC peer link - port channel trunking all VLANs. (Is this even needed)?Switch 1 = VRRP M...
Hello Team, I need your comments on attached DC Design for its traffic flow . any suggestsion will be appreciated. ? Regards
Dears,We have two nexus 7k switches, two 5k switches, 2k switch and other access switches on an implementation project.what is the question should i ask customer for?thanks
All, I have a Cisco 3850 fiber switch with a single 10G link to a Cisco Nexus 7009 ("N7K"). The N7K links to the fiber switch's Te1/0/12. What I am seeing in the CDP table is switch2 and switch6 are also showing up via Te1/0/12. Switch2 is on Te1/0...
Hello All, Working with a customer who has a data centre interconnect terminating on their nexus 9K switches into 10Gb interfaces. The interconnect has only 4Gb of bandwidth. We need to implement a shaping policy on the Nexus to limit all outbound tr...
Resolved! Nexus with BGP and ASA
So based on the following: https://community.cisco.com/t5/switching/issue-with-routing-over-nexus-7000-vpc-peerlink/td-p/1827500 https://adamraffe.com/2013/03/08/l3-over-vpc-nexus-7000-vs-5000/ http://bradhedlund.com/2010/12/16/routing-over-nexus...
Hi Support, Been trying to get my head around on how to get it working but still no luck. Firstly, let me say that i am new to Nexus Technology so i only based on Cisco Articles configurations. Any help would be highly appreciated. Basically, my ...
Hi, I am little confused on DCNM licensing. I need it for Nexus9300 switch. My question is do I need a license for each unit link for 10 switches we need 10 DCNM licenses or its only 1? CAn you please share me any link to study.
Hi! I have googled and searched the forums hi and low and I have not found the answer. If someone already has answered this please let me know. We have a network with 8x N5k switches (4 pairs). 2 of them acts as spine and the rest are leaf’s with f...
Hi all, I am wondering about CEF adjacency watermarks on Catalyst / Sup2T platforms / MPLS environment.Consider the following output:Switch#sh platform hardware cef adjacencies resource-levelWatermarks apply to regions available for allocation and no...
Hi we are installing two 9706 The customer ask to have a reverse air flow on fans due the particular data center environment. Is it posible? Thanks Walter
