While migrating away from a legacy setup, we're adding a bunch of 150AX into our production network which will live on different VLANs. These VLANs are routed transparently, meaning traffic can flow freely between them. After adding two 150AX on VLA...
I am writing this with genuine disappointment. I have been a loyal Cisco small-business customer for years, and my RV345 was the backbone of my network — dual WAN, site-to-site IPsec VPN, solid rackmount build, and a CLI that just worked.A few days a...
I have a C12008T-D. Latest firmware. Created VLANS. When I go to join and change Access VLAN ID to correct assignment and the same for General PVID the WEB GUI sticks and have to unplug and plug back in to regain access after I apply. Seems to be...
Hi,So we recently used CBD for the first time to schedule firmware upgrades to our switches. All succeeded except for one C1200 (all are either C1200 or C1300). It gave the following error:Internal error (java.lang.NullPointerException)I can't find...
I have a similar question as this old one: https://community.cisco.com/t5/cisco-business-dashboard/stop-autodiscovery-just-monitor-static-devices-in-inventory/td-p/4568247I don't necessarily need auto-discovery turned off, but I do want it to stop at...
Hello team,We have a client running a Cisco RV340 router where the evaluation security license has expired (smart_agent: SA-Error: %SMART_LIC-3-EVAL_EXPIRED_WARNING).Could you please confirm the official status on two points so we can advise our clie...
I need to change the name in Pearson Vue in order to book an exam. I is different from my Netacad name.
Hi,product being old I am unable to open a TAC case. The hardware is v1 most probably:Model Name SRW2048Hardware Version 00.03.00Boot Version 1.0.0.04Firmware Version 1.2.1I would like to update first the Bootloader to 1.0.0.06 and then to update the...
Hello,I'm posting this message to report a software regression that affects the "11.2.4" (ATA19x.11-2-4MPP0001-115) firmware version of the ATA191-MPP.Affected versions and configuration: The issue is encountered when using IPv6 only network for SIP ...
Hello everyone,My Cisco SG350-10 switch is unable to complete its boot sequence. Unfortunately, it always stops with the following error:HALP_config_poe_number_of_poe_devices is Zero: Failed on init (This message was captured through the rear se...
I want to configure my RVS4000 router but find that I am unable to login to the 192.168.1.1 site to do so. The "admin" username and password is not working. Maybe I do not have to as my internet connection seems to be working fine. ...
Setup: Cisco C1300-12XT-2X, firmware 4.1.9.85 (latest). Interface te1/0/13 is an 802.1Q trunk to a WatchGuard Firebox M690 (WG physical interface 10, also configured as a tagged trunk).Trunk config on te1/0/13:interface TenGigabitEthernet1/0/13switch...
1- C1300-48FP-4X Catalyst 1300 - 38876627+48-Port GE, Full POE, 4X10G SFP2- C1300-24FP-4X Cisco C1300 - 30798414Switch, 24x PoE+ 370W/4x 10G SFP+/Rackmountable May i know if this switches are out of support ?
Hi,we are using the Cisco C1300-24T-4G for some time and recently we found out that a new hardware revision has been released. The PCN Cisco provided states that only the label "country of origin" changed but we run into problems when we install firm...
I did a config backup.I downloaded 1.0.0.3.26 and did the update (without reset to factory checked).When completed, the webgui login page was corrupt. It had spinning icon beside what should be the login button. see pic.I tried old logins, but i dont...
